WARNING
Electrical Shock Hazard
Disconnect power before making electrical connections.
Connect ground wire to green ground screw in terminal box.
Failure to do so can result in death or electrical shock.
to light
groundbulbs wires
| terminal |
| box |
| connector |
| blower |
| wiring |
| connector |
| black wires |
power | white wires |
supply | |
wiring | |
| connectors |
18a.
For models requiring direct wiring:
Connect white wiring from the terminal box, light harness and power supply wiring together with
Connect black wiring from the terminal box to power supply wiring with
Connect the power supply ground wire and the green ground wire inside the terminal box under the terminal box ground screw.
Use caulking to seal wire opening. Replace terminal box cover.
For cord connected models:
WARNING
Electrical Shock Hazard
Plug into a grounded
Do not remove ground prong.
Do not use an adapter.
Failure to follow these instructions can result in death, fire, or electrical shock.
For your personal safety, this range hood must be grounded. To minimize possible shock hazard, the cord must be plugged into a mating,
If mating outlet is not available, it is the responsibility and obligation of the customer to have a properly grounded, 3- prong outlet installed by a qualified electrician.
Do not use an extension cord.
Using a
Follow Power Cord Kit instructions for connecting wiring.
Replace terminal box cover.
19a.Turn power supply on.
Copies of standards listed may be obtained from:
*National Fire Protection Association Batterymarch Park
Quincy, Massachusetts 02269
Use & Care
Information
Use this range hood only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. Before installation and before servicing or cleaning range hood, switch off power at service panel and lock service panel to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
Operation of range hood
For best results, turn range hood fan on at beginning of cooking and allow it to run until all smoke and odors are removed from room.
To adjust fan speed:
Turn fan speed control to desired setting between “Hi” and “Lo”. Speed may be changed anytime during range hood operation.
To turn range hood light “ON” and “OFF”: Turn light control to operate light “ON” or “OFF”. Light may be turned to “OFF” or “ON” anytime during range hood operation.
“Night” light setting:
Turn light control to “Night” setting when you need the light dimmed for use as a night light.
Care of range hood
Filters:
For best results, remove and clean often.
holes
filters
To remove aluminum filters:
Place finger in hole. Pull back and down.
To clean aluminum filters:
Place filters in dishwasher or hot sudsy water to clean.
To reinstall aluminum filters:
Place edge of filter in channel opening so that side is above flange. Pull back. Press filter into position.
When it's time to replace your aluminum filter:
1.Choose your filter order number. 30" Hood Model RH8330: Order Filter no. 883276
36" Hood Model RH8336: Order Filter no. 883277
2.Call Whirlpool's Telesales line at
3.Give the Telesales Representative the part number needed.
4.The Representative will give you the current price.
5.Place your order using your Master Card ®, Visa ® or Discover ® credit card.
6.If you wish: mail a check or money order to:
Whirlpool Corporation
1900 Whirlpool Drive
LaPorte, IN
Attn: Accessory Accounting
7.Be sure to ask the Telesales Representative about the wide variety of other Whirlpool Product Accessories.
Blower motor:
To clean blower motor:
Clean exterior of motor with a damp cloth and
Exterior surfaces:
Clean the range hood with a mild detergent and soft cloth. Do Not use abrasive cleaners or steel wool.
Light:
Do Not use bulbs larger than 60 watts in light sockets.
To replace bulbs:
Remove three screws that hold light cover panel in place. Remove panel and set aside. Replace bulb.
Replace light cover panel before operating fan or light.
Light bulbs are not included.
