INSTALLATION REQUIREMENTS
Tools and Parts
Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
All Installations
Tools needed:
Pliers | ||
screwdriver | ||
| ||
Phillips | Utility knife | |
screwdriver | ||
| ||
5/16” and 1/4” | UL listed or CSA | |
nut drivers or | approved | |
hex sockets | wire connectors* | |
Measuring tape | Small level | |
or ruler | ||
| ||
10” adjustable wrench | 5/8” | |
that opens to | ||
wrench | ||
|
*Must be the proper size to connect your household wiring to
Other useful items you may need:
Flashlight | Bath towel |
Shallow pan | Wood block |
Parts supplied:
2 - Drain hose clamps Drain hose | 2 - #10 x 1/2” |
(1 large and 1 small) | |
| screws |
Silver Green
Make sure all these parts are included in the literature package.
Parts needed:
90˚ Elbow fitting with | Teflon® tape or pipe joint |
3/8” N.P.T. external threads | compound |
(the other end must fit your |
|
water supply line) |
|
Other parts you may also need:
Side mounting kit | Masking or | |
(38.1– 5.0 cm) | for solid surface | duct tape |
countertops |
| |
clamps (3 max) | (Part No. 8212560) |
|
NOTE: Parts available for purchase in plumbing supply stores. Check local codes. Check existing electrical supply. See “Electrical Requirements” section. It is recommended that electrical connections be made by a licensed electrical installer.
In addition, for first time installations
Tools needed:
Electric drill |
|
with 1/2", 3/4” |
|
and | Small |
saw bits | tubing cutter Wire stripper |
Parts needed:
Copper tubing (3/8” See “Electrical Requirements” section O.D. suggested) or
flexible braided water supply line
Location Requirements
Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must provide clearance between motor and flooring. Motor should not touch the floor.
Do not install dishwasher over carpeted flooring.
Protect dishwasher and water lines leading to dishwasher against freezing. Damage from freezing is not covered by the warranty.
A side panel kit is available from your dealer for installing your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part No. 4396277) is available from your dealer for installing underneath the countertop, but is not required.
Check location where dishwasher will be installed. The location must provide:
•easy access to water, electricity and drain.
•convenient access for loading and unloading dishes. Corner locations require a 2” (5.1 cm) minimum clearance between the side of the dishwasher door and the wall or cabinet.
•square opening for proper operation and appearance.
•cabinet front perpendicular to floor.
•level floor. (If floor at front of opening is not level with floor at rear of opening, shims may be needed to level dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions and ensure dishwasher is level if the floor in the dishwasher opening is uneven (example: flooring extends only partway into opening).
NOTE: To prevent shifting during dishwasher operation, shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a location where it may be subject to freezing, have it winterized by authorized service personnel.
Make sure pipes, wires and drain hose are within the |
|
shaded area shown in the “Product and Cabinet |
|
Opening Dimensions” section. | 3 |
|
® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.
