Whirlpool WRF560SEYW, WRF560SMYW, WRF560SMYM, WRF560SEYB, WRF560SEYM Water Dispenser

Models: WRF560SEYM WRF560SEYB WRF560SMYM WRF560SMYW WRF560SEYW

1 84
Download 84 pages 15.57 Kb
Page 15
Image 15

Additional Features

Door Open Alarm

The Door Open icon lights up whenever either door is opened.

When either door is open for 5 minutes and cooling is on, an alert tone will sound three times, and the Door Open icon will flash seven times. This pattern will repeat every 2 minutes until all the doors are closed properly. The feature then resets and will reactivate when either door is left open again for

5 minutes.

NOTES:

To mute the audible alarm while keeping the doors open, such as while cleaning the inside of the refrigerator, press any button on the control panel. The alarm sound will be temporarily turned off, but the Door Open icon will still be displayed on the dispenser control panel.

Both doors must be fully closed to turn off the Door Open icon.

Fast Cool

The Fast Cool feature assists during times of high refrigerator use, full grocery loads or temporarily warm room temperatures.

Press FAST COOL to set the freezer and refrigerator to the coldest temperature settings. Press FAST COOL again to return to the selected temperature set point.

NOTES:

The Fast Cool icon will be illuminated while the refrigerator is in Fast Cool mode.

The Fast Cool feature will turn off automatically after 24 hours.

Moisture Control

The moisture control feature turns on a heater to help reduce moisture on the door hinge seal. Use in humid environments or when you notice moisture on the door hinge seal. The refrigerator uses more energy when Moisture Control is on.

NOTE: The moisture control icon will light up to indicate the feature is on.

To turn on/off the moisture control feature:

Internal Control Panel - Press and hold MOISTURE CONTROL for 3 seconds.

External Control Panel - Press and hold LIGHT for 3 seconds.

Water Filter Status Light and Reset

The filter reset control allows you to restart the water filter status tracking feature each time you replace the water filter. See “Water Filtration System.”

Press and hold WATER FILTER for 3 seconds, to reset the water filter status to Good. The water filter icon will turn blue.

Water Dispenser

(on somemodels)

IMPORTANT:

Allow 3 hours for the refrigerator to cool down and chill water.

Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

The dispensing system will not operate when the refrigerator door is open.

Flush the Water System

Air in the water dispensing system can cause the water dispenser to drip. After connecting the refrigerator to a water source or replacing the water filter, flush the water system.

Flushing the water dispensing system forces air from the water line and filter and prepares the water filter for use. Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

1.Using a sturdy container, depress and hold the water dispenser paddle for 5 seconds.

2.Release the dispenser paddle for 5 seconds.

3.Repeat steps 1 and 2 until water begins to flow.

4.Once water begins to flow, continue depressing and releasing the dispenser paddle (5 seconds on, 5 seconds off) until a total of 4 gal. (15 L) has been dispensed.

Dispense Water

IMPORTANT:

The dispensing system will not operate when the refrigerator door is open.

The display screen on the dispenser control panel will turn off automatically and enter “sleep” mode when the control buttons and dispenser paddles have not been used for

2 minutes or more. While in “sleep” mode, the first press of a control button will only reactivate the display screen, without changing any settings. After reactivation, changes to any settings can then be made. If no changes are made within 2 minutes, the display will re-enter “sleep” mode.

To dispense water:

1.Press a sturdy glass against the water dispenser paddle.

2.Remove the glass to stop dispensing.

Air Filter Status Light and Reset

The filter reset control allows you to restart the air filter status tracking feature each time you replace the air filter. See “Install Air Filter.”

Press and hold AIR FILTER for 3 seconds, to reset the air filter status to Good. The air filter icon will turn blue.

15

Page 15
Image 15
Whirlpool WRF560SEYW, WRF560SMYW, WRF560SMYM, WRF560SEYB, WRF560SEYM installation instructions Water Dispenser