PROGRAMMING
PROGRAMMING YOUR THERMOSTAT
This section will help you plan your thermostat’s program to meet your needs. For maximum comfort and efficiency, keep
the following guidelines in mind when planning your program.
•When heating (cooling) your building, program the temperatures to be cooler (warmer) when the building is vacant or during periods of low activity.
•During early morning hours, the need for cooling is usually minimal.
Planning Your Program
Look at the factory preprogrammed times and temperatures shown in the sample schedule. If this program will suit your needs, simply press the RUN/HOLD button to begin running the factory preset program.
If you want to change the preprogrammed times and temperatures, follow these steps.
Determine the time periods and temperatures for your program. You must program four periods for each day. However, you may use the same heating and cooling temperatures for consecutive time periods. You can choose start times, heating temperatures, and cooling temperatures independently (for example, you may select 5:00 AM and 70° as the daily 1st period heating start time and temperature, and also choose 7:00 AM and 76° as the daily 1st period cooling start time and temperature).
Use the table to plan your program time periods and the temperatures you want during each period. Fill in the complete table to have a record of your programs.
Entering Your Program
Set Current Time and Day
1.Press TIME button once. The display will show the hour only.
EXAMPLE:
2.Press and hold either 
or 
until you reach the correct hour and AM/PM designation (AM begins at midnight; PM begins at noon).
3.Press TIME once again. The display window will show the minutes only.
EXAMPLE:
4.Press and hold either 
or 
until you reach the correct minutes.
5.Press TIME once again. The display will show the day of the week.
6.Press 
or 
until you reach the current day of the week.
7.Press RUN/HOLD once. The display will show the correct time, day, room temperature and
Enter Heating Program
1.Move the SYSTEM switch to HEAT.
2.Press PRGM once. “Mo Tu We Th Fr Sa Su” (indicating daily program) will appear in the display. Also displayed are the currently programmed start time for the 1st heating period and the currently programmed temperature
(flashing).
EXAMPLE:
This display window shows that for the 1st weekday period, the start time is 6:00 AM, and 70° is the programmed temperature (this example reflects factory preprogramming).
3.Press 
or 
to change the displayed temperature to your selected temperature for the 1st heating program period.
4.Press TIME once (the programmed time will flash). Press 
or 
until your selected time appears. The time will change in 15 minute increments. When your selected time is displayed, press TIME again to return to the change temperature mode.
5.Press PRGM once. The currently programmed start time and setpoint temperature for the 2nd heating program period will appear.
6.Repeat steps 3 and 4 to select the start time and heating temperature for the 2nd heating program period.
SAMPLE
Heating/Cooling Schedule Plan
(Factory Program)
|
|
| Daily |
|
|
|
|
|
|
| Period | Start | Temp | |
| Time | |||
|
|
|
| |
|
| 1ST | 6:00 AM | 70F |
|
|
|
|
|
HEAT |
| 2ND | 8:00 AM | 62F |
|
|
|
| |
| 3RD | 5:00 PM | 70F | |
|
| |||
|
|
|
|
|
|
| 4TH | 10:00 PM | 62F |
|
|
|
|
|
|
| 1ST | 6:00 AM | 78F |
COOL |
|
|
|
|
| 2ND | 8:00 AM | 85F | |
|
|
|
| |
| 3RD | 5:00 PM | 78F | |
|
| |||
|
|
|
|
|
|
| 4TH | 10:00 PM | 82F |
|
|
|
|
|
Heating/Cooling Schedule Plan
|
|
| Daily |
|
|
|
|
|
|
| Period | Start | Temp | |
| Time | |||
|
|
|
| |
|
| 1ST |
|
|
|
|
|
|
|
HEAT |
| 2ND |
|
|
|
|
|
| |
| 3RD |
|
| |
|
|
|
| |
|
|
|
|
|
|
| 4TH |
|
|
|
|
|
|
|
|
| 1ST |
|
|
COOL |
|
|
|
|
| 2ND |
|
| |
|
|
|
| |
|
|
|
|
|
|
| 3RD |
|
|
|
|
|
|
|
|
| 4TH |
|
|
|
|
|
|
|
7
