NOTE: ALL SETTINGSPROTECTIONCAN BE VIEWED ON THE REMOTE DISPLAY
a)Operating Condition - The protective device will be tripped, and the unit will shut off under these two conditions:
•Cooling: (1) Outdoor air temperature is over 109oF (*43oC). (2) Room temperature is below 61oF (16oC).
•Heating: (1) Outdoor air temperature is below 23oF
•Dry: Room temperature is below 61oF (16oC).
If the air conditioner runs in COOLING or DRY mode with door or window opened for a long time when relative humidity is above 80% condensation may drip down from the outlet.
b) Features of Protector
•Restarting the unit at once after operation stops or if changing mode during operation, you need to wait 3 minutes.
•Connect to power supply and turn on the unit at once, it may start 20 seconds later.
•If the plug is taken out, when you restart the appliance, it will return to the original mode, TIMER ON and TIMER OFF must be set again.
CONDENSATION ELIMINATION SYSTEM
While air conditioning mode, the unit automatically dehu- midifies the air in the room. The water from dehumidifica- tion is stored in a collecting tank and then is immediately “evaporated” and evacuated via the exhaust port. However, when it is extremely humid, the water in the col- lecting tank may fill up. In this case, the Water Full Indicator Light turns on and the air conditioner switches itself off.
It is then necessary to drain the water through the conden- sate drain hose. For draining instructions, please refer to the “Long Term Storage” instructions under the “Cleaning the Unit” instructions.
CLEANING AND STORAGE
Before cleaning the unit, turn it off and unplug it from the outlet. For safety reasons, never wash the air conditioner by hosing it down or wiping it with a dripping wet sponge or cloth.
Exterior surfaces of the unit
•Clean the air conditioner by using a damp sponge, and dry it with a clean, soft cloth.
•Never use alcohol or any product containing solvents.
•Never sprinkle water onto the unit. This may cause an electric shock.
Air filter
The air filter located on the back of the unit, collects dust contained in the air. To keep the dust from clogging the
unit, your unit must always be used with its air filter.
•The build up of dust reduces the efficiency of the air conditioner. Therefore, the air filter must be cleaned every 100 hours of use, and every two weeks if the unit operates in a dusty atmosphere.
•If the filters are obstructed, the air conditioner will be less efficient.
•To remove the air filter, place fingers in the notch just under the top of the air filter handle and pull up.
•Clean the filter with a vacuum cleaner. If the filter is very dirty, you can wash it in warm water (never use hot or soapy water). Make sure that the air filter is completely dry before putting it back in the unit.
•Do not bend the filter.
LONG TERM STORAGE
At the end of the season, or when you do not plan to use the unit for an extended period of time, we recommend that you take the following steps:
Drain Hose 
Drain excess water from the drainpan from the Drain Hose
•Run the unit for 3 to 4 hours in fan mode. This will thoroughly dry the inside of the unit.
•Disconnect the unit and wrap the power cord and plug around the cord hooks in the back.
•Take out the batteries from the remote.
•Remove the air hoses and cover the air intake and air outtake holes with the included covers.
•Clean the unit and air filter and store it in it’s original packaging, protecting it from dust.
•Store the unit in an upright position. Keep it in a cool, dry place and away from sunshine.
Using the unit in wine cellars or in any room with a temperature under 61oF is not recommended.
ENERGY SAVING TIPS
•Blocking of the filter reduces the efficiency of the air and increases its power consumption by up to 6%.
•Avoid opening doors frequently.
•Each person present in a room provides between 100 Watts and 150 Watts of heat. Consequently, the more people there are in a room, the less effective the unit will be in cooling.
•To ensure the optimal efficiency of the unit, we advise you to keep doors and windows closed, and to take into account the surface of the walls and windows exposed to the sun. In this case, in order to optimize the functioning of your air conditioner, we recommend partially closing window coverings.
SPECIFICATIONS
Cooling Capacity: | 12,000 BTU/Hour |
Heating Capacity: | 4100 BTU/Hour |
Power Input: Cooling | 1450Watt/14.5Amps |
Heating | 1350 Watt/12Amps |
Energy Efficiency Ratio: | 8.2 |
Coolant: | |
Moisture Removal: | 2.5 Pints / Hour |
| (60 Pints / Day) |
Airflow Volume: | 177 CFM (Cubic Feet / Minute) |
Noise Level: | 46 db |
Compressor Type: | Rotary |
Operating Temperature Range:
Cooling:
Heating:
Voltage/Frequency:
Ionization Capacity:
Product Dimension (WxHxD):
17.7” (W) x 32.28” (H) x 18.3” (D) 45cm(W) x 82cm(H) x 46.5cm(D)
Product Net Weight: | Net Weight: 83lbs. / 37.6kgs. |
1.All wiring must comply with local and national electrical codes and be installed by a qualified electrician. If you have any questions regarding the following instructions, contact a qualified electrician.
2.Check available power supply and resolve any wiring problems before installation and operation of this unit.
3.This product must be grounded. If it should malfunction or breakdown, grounding provides
a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment grounding conductor and a three prong grounding plug. The plug must be plugged into an appropriate three prong outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not use plug adapters or extension cords with this unit.
SAFETY POWER SUPPLY CORD
This unit is provided with a Leakage Current Detection and Interruption circuit (LCDI) built into the plug of the power supply cord. This device provides protection to reduce the risk of fire due to arcing faults in the
PLUG TESTING INSTRUCTIONS: TO BE DONE WHILE PLUG IS IN OUTLET.
1.PRESS TEST BUTTON. UNIT SHOULD TRIP.
2.FIRMLY PRESS RESET BUTTON FOR USE.
DO NOT USE IF ABOVE TEST FAILS.
The conductors inside this power supply cord are sur- rounded by shields which monitor the leakage current. These shields are not grounded. Periodically examine the cord for any damage. If the shield gets exposed, immedi- ately unplug the power supply cord and do not use the unit. Do not repair a damaged cord. Replace the damaged cord only with a new replacement power supply cord obtained from the manufacturer.
In the event the LCDI Plug of the power supply cord trips by itself, then first examine the cord for any damage. If there is no damage to the cord then press the RESET Button. If the LCDI Plug trips again, then immediately unplug the power supply cord. Replace the damaged cord with a new replacement power supply cord.
To obtain a new replacement power supply cord contact WindChaser Products Customer Service at:
(800)
Do not use The TEST and RESET Buttons as an on / off switch. They are only meant to be used to periodically check the LCDI plug.
10 | 3 |
