![](/images/new-backgrounds/1230146/2301465x1.webp)
Quick Reference Guide
NOTICE!
This model is PRESET for DIRECTV® receivers.
If you have a DISH Network® or ExpressVu® (Canada) receiver, you must change the numbered switches inside the dome.
TO CHANGE SWITCHES INSIDE DOME —
1.Remove screws holding dome to base and remove dome. Place dome in safe spot to avoid damage. Switches will be set at 101° for DIRECTV®. You may be changing these switches.
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
0 = up | 0 | 0 0 0 0 0 | 0 1 |
1 = down
(#1 represents Switch DOWN; #0 represents Switch up)
Sat. Rcvr. Mt. Option |
| Switch Set Position |
|
|
|
| ||
..................................... | 1. | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
DIRECTV | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 |
(FACTORY PRESET) |
|
|
|
|
|
|
|
|
DISH NETWORK | 0 | 0 | 0 | 1 | 0 | 0 | 1 | 1 |
ExpressVu | 0 | 1 | 0 | 1 | 1 | 0 | 1 | 1 |
|
|
|
|
|
|
| ||
0= up |
| 1= down |
|
|
|
|
SWITCH SETTINGS SHOWN BELOW
2. Determine which programming you will be using. This will determine how you set your switches.
For DISH Network set switches to 119°. | For ExpressVu®, set switches to 091°. |
0= up
1 | 2 | 3 | 4 |
| 5 | 6 | 7 | 8 |
|
|
0 | 0 | 0 |
| 1 | 0 | 0 | 1 | 1 | 1= down | 0= up |
|
|
|
|
|
|
| LEC |
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
| VEHIOFT |
|
|
|
| FRON | Center line of vehicle |
|
| |
MOUNTING |
| MVMV3500A- |
1 2 3 4 5 6 7 8
0 | 1 | 0 | 1 | 1 | 0 | 1 | 1 |
|
CABLES EXIT
FROM REAR
VEHICLEOF
BACK
1= down
Operation (Vehicle MUST be stationary!!)
1.Turn on receiver and television set. The MV3500A must be connected to a receiver that is plugged into 120 VAC.
2.Verify that you are getting the receiver’s menu
screens on the television. These screens are available with or without the dish finding the signal.
3.Turn the power switch on for the MV3500A. The dish will detect if it is already on a satellite signal. If it detects a signal, the dish will move to check its al- ternate satellite and then move back to the original satellite signal that it was on.
4.If no signal was detected, the dish will begin its search to locate the primary satellite. Once the dish locates a signal, it will pause long enough to identify which satellite it has located. This may or may not be
visible on your receiver’s point dish screen.
5.After the unit has verified that it has the correct satellite, it will move to check the alternate satellite and move back to the primary satellite to complete the search routine.
6.If you do not have signal, see Troubleshooting, p.11.
NOTE: Because the MV3500A uses information from the last location that it was on a signal, satellite acqui- sition may take longer if the dish is inactive over long distance traveling.
DirecTV must be set to the “two” satellite, oval dish setting. Refer to your receiver manual.
DISH Network receivers must have the check switch set for “SW42”. See page 4.
3