Winegard MV3535A, MV3500A manual Coax Cable Routing, Installing the Power Switch

Models: MV3535A MV3500A

1 12
Download 12 pages 27.59 Kb
Page 8
Image 8

Installation

Cable entry installation —

1.Decide the best location for the cables to enter the vehicle, and the location of the power switch and receiver (see “Installing the switch and receiver”on pages 9 and 10). Drill a 1/2” hole in the roof, push wires inside. Make proper connections.

You must have filtered +12 VDC power source.

2.If installing a second receiver, route second coax cable (not supplied) through empty Heyco into base. Connect to secondary coax connection point. See page 6.

3.Place cable-entry plate over hole and cables. Screw in place. Seal plate and screw holes with approved sealant (not included).

4.Depending on the length of the cable on the roof, you may need to use cable clamps or wire ties (not provided) between the unit and your cable-entry plate.

Clamping the cable every 12”-16” should eliminate any unnecessary cable movement.

COAX CABLE ROUTING

PRIMARY

RECEIVER

(GRAY WIRE)

MOVIN’ VIEW

SECONDARY

RECEIVER (NOT

(White WIRE-

SUPPLIED)OEM ONLY)

INSTALLING THE POWER SWITCH

1.Choose a location to install the Movin’ View power ON/OFF switch. Remember when selecting a location that you will need to run the +12VDC power cable from the Movin’ View antenna to the switch. Be sure the switch is in the OFF position before continuing. See Figure 7 page 8.

!DO NOT CUT DATA CABLE SHORT!

Wall or panel mount: Drill 1-1/4” hole, pull wires through wall or panel.

2.Connect the ground wire from the vehicle and the

BLACK ground wire from the antenna together, using large yellow flag connector.

3.Connect the YELLOW flag connector to the silver spade on the switch.

4.Connect the RED wire from the antenna to the small RED flag connector.

5.Connect small RED flag connector to center spade on switch.

6.Connect the +12 V power wire from the vehicle to a small RED flag connector.

7.Connect small RED flag connect to isolated spade on switch.

INSTALLING THE POWER SWITCH DIAGRAM

FIGURE 7

ON/OFF ROCKER SWITCH

WITH LIGHT

(Shown in OFF position.)

steps 2 & 3

STEPS 6 &7

Two GROUND wires

+12 v FROM VEHICLE

1 frOm vehicle

 

1 Black wire from

 

  SATELLITE DISH

sTEPS 4 & 5

 

 

RED POWER

 

WIRE FROM

 

DISH

HD Ready

The power wire is bundled with a data cable for con- necion to the Winegard HD Satellite Interface. DO NOT CUT DATA CABLE SHORT! If you will not connect the HD Satellite Interface at this time, hide the data cable behind the wall plate for future use.

8

Rev. 7/07

Page 8
Image 8
Winegard MV3535A, MV3500A manual Coax Cable Routing, Installing the Power Switch

MV3535A, MV3500A specifications

The Winegard MV3535A and MV3500A are high-performance outdoor HDTV antennas designed to provide users with exceptional reception and signal quality, making them ideal choices for both urban and rural installations. These antennas are engineered to capture over-the-air digital television signals, allowing users to access local channels in HD without a cable subscription.

One of the standout features of the MV3535A is its advanced multi-directional reception capability, which enables it to receive signals from multiple directions. This is particularly beneficial for users located in areas with broadcasting towers situated in various locations. The MV3535A’s design incorporates a combination of elements, including a powerful preamplifier that amplifies weak signals, ensuring clearer picture quality even in challenging reception environments.

Similarly, the MV3500A also boasts a multi-directional design along with a robust construction that withstands various weather conditions. This model is built with a die-cast aluminum housing and UV-resistant materials to ensure durability against sun exposure, rain, and snow. Both models come equipped with low-noise amplifiers, minimizing interference and enhancing signal clarity, which is essential for receiving HD channels.

In terms of installation, the Winegard MV3535A and MV3500A are designed for user convenience. They come with a mounting kit that makes it easy to attach the antenna to roofs and poles, providing flexibility in installation height for optimal signal reception. The antennas are lightweight yet sturdy, making them manageable for DIY enthusiasts.

One of the key technologies integrated into both the MV3535A and MV3500A is the patented Wing and Reflector design. This innovative feature maximizes signal capture by focusing on the broadcast signals while reducing interference from other sources, which can be particularly beneficial in areas with overlapping signals.

Overall, the Winegard MV3535A and MV3500A are excellent choices for anyone seeking reliable over-the-air television reception. Their advanced technologies, durable construction, and user-friendly installation make them valuable additions for cord-cutters looking to enhance their viewing experience with high-quality HD channels. Whether enjoying local news, sports, or favorite shows, these antennas deliver impressive performance suited for diverse environments.