User manual W3532
- 13 -
Fig.11e
The engine monitor is an independent LCD counter for motor-
hours, a speed indicator and a measuring gauge for
maintenance. Energy is supplied from a lithium battery The
conductor around the sparking plug ensures both functions; the
signal of the counter for the revolutions, as well as an indicator
that the engine is running. For maintenance, this counter is
used in such a manner that the maintenance interval is set and
at the moment of expiration the counter reports the
requirement for the maintenance of the engine. Before setting
the counter each time, make sure that the engine is
disconnected. If it is necessary to unwind the black conductor
from the cable of the spark plug, for re-winding it is necessary
to perform only 3 ÷ 4 turns (otherwise the counter will not
show the correct values of the revolutions within the whole
range of the revolutions of the engine).
1. Setting the reading of the signal from the
spark plug
Press and hold button S1 for 4 seconds. LCD displays 01 (the
spark plug is activated twice per revolution), 02 (once per
revolution), 03 (each further revolution), 04 (displays only
hours not revolutions). As soon as you find the required
diagram, release button S1. The LCD will flash 8-10s and
return to the overall regime of the counter. Pre-setting of the
standard counter is 02 (once per revolution). This pre-setting
can be changed during production.
2. Setting the timer for maintenance
Press and hold button S2 for 4 seconds. The number which is
in the correct position will start to flash and the SERVICE
icon will be displayed. By pressing and holding button S1 the
number will start to change. As soon as you achieve the
required number, release button S1 and press button S2 for 1
second, it will switch to the setting the next number. Repeat
the above-mentioned steps for as long as you set the service
interval. After 14-16 seconds without pressing buttons the
counter will return to the basic regime.
3. Activation of the maintenance timer
Press and hold for 4 seconds, buttons S1 and S2 at the same
time. Two numbers will be displayed for 20 seconds and then
the counter will return to the basic regime. If the engine is in
operation and the time for the maintenance achieved 0, the
service icon will appear.
4. Checking the interval for maintenance
Press and hold for 4 seconds, button S2 for as long as the
remaining time of your interval appears. If you want to set a
new interval, repeat steps 4 and 5. Each time you want to see
the remaining time from the set interval, press and hold button
S2.
5. Deletion of the maintenance icon
Press and hold buttons S1 and S2. The service icon will be
disconnected. The time for the maintenance will automatically
return to the number which was previously pre-programmed.
6. Display only hours
Press and hold button S1 for as long as 04 is displayed.
Release the button and the display will return to the overall
hours after 8-10 seconds. If the engine is in operation, the
display shows only hours, it will not display the revolutions
and the hour icon will flash.
7. Resetting the total hours and the timer for the
maintenance
Press and hold button S1 for as long as 05 is displayed.
Release the button and the display will return to total hours
after 8 seconds. Press and hold for 20 seconds, buttons S1 and
S2 at the same time, the counter will be completely reset. The
complete reset function may be excluded during production.
After each use it is necessary to clean the self-moving rotary
cutter from the outside, to empty the bag and to shake it to
remove the remainders of grass and earth.
Washing – Fig.12
Washing is to be performed on a firm base with the bag
attached. Washing the inside parts of the cutter and the
throwing mechanism is to be performed with the disconnected
drive of the cutting mechanism with a stream of water lasting
several minutes or with the activated drive of the cutting
mechanism and the connection of the pressured water
gradually to both connections of the ¾” neck located on the
shell of the cutting mechanism. Then disconnect the drive of
the cutting mechanism, stop the machine, remove the bag,