Spindles and Blades
REF | PART |
| QTY | DESCRIPTION |
1 | 3761 |
| 1 | Spindle assembly (for left hand rota- |
|
|
|
| tion) |
2 | 5089 |
| 2 | Seal |
3 | 4114 |
| 1 | Sleeve |
4 | 4115 |
| 1 | |
5 | 4107 |
| 2 | Bearing cone |
6 | 4117 |
| 1 | Housing with cups |
7 | 4106 |
| 2 | Bearing cup |
8 | 1972 |
| 1 | Grease fitting |
9 | 28897 |
| 1 | Spindle shaft with left hand thread |
10 | 4110 |
| 1 | Shoulder washer |
|
|
|
| L59 & FM48) |
10 | 13409 |
| 1 | Shoulder washer 3 diameter (for |
|
|
|
| L306) |
11 | 5081KT |
| 1 | |
|
|
|
| on RM48 and FM48) |
11 | 26875KT | † | 1 | |
|
|
|
| on RM48) |
11 | 23825KT |
| 1 | |
|
|
|
| dard on L59) |
11 | 25997KT | † | 1 | |
|
|
|
| on L59) |
11 | 13404KT |
| 1 | |
11 | 28328KT | † | 1 | |
|
|
|
| on L306) |
12 | 1015826 |
| 1 | Blade bolt and washer kit (For FM48 |
|
|
|
| & L59) |
13 | 692 |
| 1 | 5/8 Flat washer |
14 | 10635 |
| 2 | 5/8 ID Cup washer (for FM48 & L59) |
14 | 13401 |
| 2 | 1" ID x |
|
|
|
| L306) |
15 | 10718 |
| 1 | Special |
|
|
|
| L59) |
15 | 24184 |
| 1 | Special |
16 | 13402 |
| 1 | Clutch disk 3" diameter |
17 | 13403 |
| 1 | Blade stop |
18 | 13405 |
| 1 | Shim washer |
19 | 12313 |
| 1 | 5/8 ID x 1" OD x 13/16 sleeve, hear |
|
|
|
| treated |
20 | 13451 |
| 1 | Special heat treated washer |
22 | 4902 |
| 1 | Spindle lock wrench (used on FM48) |
|
|
|
| |
22 | 2974 |
| 1 | Spindle lock wrench (used on L59 & |
|
|
|
| L306) |
23 | 3490 | ‡ | 1 | Blade bolt wrench |
NOTE: Repair shaft 9 and repair sleeve 3 do not have a hole drilled in them for pin 4. After new parts have been assembled and proper bearing adjustment obtained, drill a 3/16" diameter hole through sleeve and shaft. Drive in
NOTE: Left hand blade rotation for “L” series. (See page _ for right hand rotation 59’s and yellow RM48’s.)
*For maximum suction for difficult mowing.
†For use in sandy areas or where high abrasive wear occurs on fin of stan- dard blade.
‡Used on mower prior to 1964.
20 Parts | 29936 (Rev. 5/18/2007) |
|
|
