Manuals / Xantrex Technology / Marine Equipment / Marine Battery

Xantrex Technology 806-1055, 806-1020, 806-1840-01, 806-1840-02 manual Electric Shock Hazard

Models: 806-1055-02 806-1840 806-1055 806-1020 806-1840-01 806-1840-02

1 54

Download 54 pages 4.84 Kb

Page 31

AC Input Connections for the Freedom HF 1055 EMS and Freedom HF 1800 EMS Models

ELECTRIC SHOCK HAZARD

Do not alter the AC cord and its three-prong plug. The AC cord is pre- installed and pre-wired to the AC Input terminals of the unit.

Do not connect the plug to other than a properly grounded electrical wall outlet.

Failure to follow these instructions will result in death or serious injury.

TEST

TEST

RESET

RESET

to wall outlet

1.Ensure AC and DC power sources are turned off.

2.Connect the three-prong plug to an AC wall outlet.

Basic Installation Procedures

This guide for use by qualified installers only.

975-0395-01-01

17

Image 31

Xantrex Technology 806-1020, 806-1840-01, 806-1840-02, 806-1055-02 806-1840 manual Electric Shock Hazard

Contents

Freedom HF Inverter/Chargers Page Document Part Number Statement of Hazard About This GuideRelated Information Electrical Shock Hazard Important Safety InstructionsExplosion Hazard Fire and Burn HazardPrecautions When Working With Batteries Risk of Damage to the INVERTER/CHARGER Precautions When Preparing to ChargeExposure to Chemicals and Gases Hazard Fire HazardLimitations on USE Precautions for Using Rechargeable AppliancesRegulatory Risk of Damage to Rechargeable AppliancesKKK Information to the User FCC Information to the UserPage Contents Page What’s In The Box Display panel is attached to the unit Materials ListInstallation Codes Safety InstructionsShock Hazard Installation Tools and Materials High Level Overview of Installation Steps Basic Installation Procedures To engine Designing the InstallationGenerator AC shore powerAC Disconnect and Over-Current Protection Device AC Cabling AC Distribution PanelsEquipment Damage AC Grounding AC Output Neutral BondingDC Cabling DC Disconnects and Over-Current Devices Ground Fault Circuit Interrupters GFCIsBatteries Splashing water or bilge water Close to the battery compartment and the AC source and loadChoosing a Location for the Unit Fire and Explosion HazardsTo mount the Freedom HF Mounting the UnitGrounding Locations Connecting the Equipment GroundGeneral AC Wiring Considerations Connecting the AC Input WiresFIRE, SHOCK, and Energy Hazards Damage other equipment Installers onlyAC Input Connections for the Freedom HF 1800 T Model Electric Shock Hazard FIRE, SHOCK, and Energy Hazards Connecting AC Output to an Existing AC CircuitAC Output Connections for the Freedom HF 1800 T Model To make a permanent connection to existing AC wiringReverse Polarity Damage GNDDC End for Freedom HF 1000, 1055, 1800, and 1800 T Connecting the DC CablesTo make the DC connections Equipment DamageFor use by qualified installers DC Grounding Anderson ConnectorsTo connect the DC ground Exposed Ignition Control Terminals To enable ignition controlTo enable ignition control and to connect auxiliary DC power Power Module For Freedom HF 1055 EMS and 1800 EMSUse by qualified installers only To mount the display panel Mounting the Display PanelTesting in Invert Mode Testing Your InstallationTo test the Freedom HF in invert mode To test the Freedom HF in shore power mode Testing in Shore Power ModeDifferent Views Drip Shield Installation For Marine InstallationsTo install the drip shields Drip Shield Installation For Marine InstallationsConfiguration Typical Marine Installation Marine InstallationPhysical Specifications SpecificationsDC Input AC Input Page Page Xantrex Technology USA Inc