Xantrex Technology HW 1000 E07 , E08 E09 E10 , E11 , E12

5–6 975-0467-01-01

E07 Over-temperature

warning Inverting • Reduce the loads connected to the AC

outlet of the unit.

• Check that the ventilation grille is not

blocked.

• Check for ambient temperature and move

the unit to a cooler location whenever

possible.

E08 not used

E09 not used

E10 High battery voltage

(> 15.5 V) AC shore

power • Check for external charging sources, such

as an over voltage alternator, and

disconnect if necessary.

• Confirm that the external charging source is

not the cause. The error may be caused by

the internal battery charger system. Call

Xantrex for support.

E11 Over-temperature

detected on the AC

transfer relay

AC shore

power • Reduce the loads connected to the AC

outlet of the unit.

• Check that the ventilation grille is not

blocked.

• Check for ambient temperature and move

the unit to a cooler location whenever

possible.

E12 Battery is bad or

external DC load is

connected to the

battery.

AC shore

power • Check the battery bank.

NOTE: The battery voltage did not rise

above 5 Vdc after 1 minute or 10 Vdc after

15 minutes.

• Check that the external DC load current

consumption is below the charging current

setting.

• Disconnect the DC load or increase the

charger current setting.

Table 5-1

Error Codes Displayed on the Display Panel Screen

Error Code Condition Mode Action

Contents

Main Page Page About Xantrex About Schneider Electric Trademarks Notice of Copyright Exclusion for Documentation About This Guide Purpose Scope Audience Organization Conventions Used Related Information WARNING CAUTION Important Safety Instructions READ AND SAVE THIS OWNERS GUIDE FOR FUTURE WARNING: Explosion hazard Personal Precautions When Working With Batteries Page Precautions for Using Rechargeable Appliances CAUTION: Equipment damage Page Contents 5 Troubleshooting Page Page Page Page Tables Page 1 Freedom HW Inverter/Charger Independent Power System Page 2 Materials List Default Settings for the Freedom HW System Table 2-1 Front Panel Freedo m HW Default Values Side Panel Rear Panel Display Panel FREEDOM HW 1000 Page Page Setting Battery Types on the Main Unit WARNING: Fire hazard Viewing Inverter/Charger Information Adjusting Feature Settings Page Page Page Page Page 4 Display Panel Operation FREEDOM HW 1000 Operating in Shore Power Mode Inverter Mode Settings WARNING: Shock hazard Note: Operating in Inverter Mode Disabling the Inverter Function Checking Battery Status Checking Output Power WARNING: Shock hazard Operating Several Loads at Once Adjusting the Audible Alarm Status LED During Inverter Mode The following summarizes the behavior of the Status LED during Inverter mode. Table 4-1 or Status LED during Inverter Mode 12.8 Page Operating During Transition Between Shore P ower and Inverter Mode Transitioning from Shore Power to Inverter Mode Transitioning from Inverter Mode to Shore Power Operating Limits Power Output Input Voltage The allowable Freedom HW input voltage ranges are shown in the following table: Inverter Loads Overload Conditions High Surge Loads Trouble Loads Over-temperature Condi tions CAUTION Battery Charging Table 4-2 Battery Charging Status LED or BUL CHg 12.8 ABS CHg 14.2 5A or 15A or 35A IN0 or In1 Select button is pressed to display present Inverter Mode aL0 or AL1 Select button is pressed to display present Alarm setting. Routine Maintenance Freedom HW Unit Batteries 5 General Troubleshooting Guidelines WARNING: Shock and Energy hazard Page Common Problems Buzz in Audio Equipment Television Reception Warning Messages Error Codes Displayed on the Display Panel Screen E01 E02 E03 E07 Table 5-1 E08 E09 E10 E11 E12 Page Troubleshooting Reference WARNING: Electrical shock and burn hazard Table 5-2 Troubleshooting Reference Table 5-2 Troubleshooting Reference Inverter Applications Resistive Loads Motor Loads Long Transfer Times High Surge When Powering Incandescent and CFL Bulbs Page Page Electrical Specifications: Inverter Mode Electrical Specifications: Charge Mode Environmental Specifications System Specifications Physical Specifications Regulatory Approvals 975-0467-01-01 A5 Regulatory Approvals Inverter Overload Operation ETL approved to CSA 107.1, UL458 Time (sec) Output Current (Amps) Invert Power Derating vs. Ambient Temperature Charger Output Current vs. AC Input Voltage Page Warranty and Return Information Warra nty What does this warranty cover and how long does it last? This Limited Warranty is provided What will Xantrex do? How do you get service? Disclaimer Return Material Authorization Policy Return Procedure If you are returning a product from outside of the USA or Canada If you are returning a product to a Xantrex Authorized Service Center (ASC) A Xantrex Out of Warranty Service Information About Your System