Yamaha DTXPRESS III Create Your Own Original Drum Kit, LayerBalance=+20 , Reverb send= 40 Reverb send level

25
Use the [SEL<]/[SEL>] buttons to move the flashing cursor
to the decay value position, then use the [VALUE–]/[VALUE+]
buttons to set the amount of decay.
A + (plus) value will produce a faster decay.
6. Try Changing the Character of the Voice
(Filter Setting).
Using the same display you can set the Filter Cutoff Frequency.
Try to change the character of the voice (the brightness of the
voice).
Press the [SEL>] button to move the flashing cursor to the
“Fc=” position, then use the [VALUE–]/[VALUE+] buttons
to set the value.
A + (plus) value will produce a brighter sound.
7. Try Adjusting the Volume Balance of the 2
Layer Voice.
If the selected drum voice is made with 2 layers (1 drum voice
made with 2 voice waves), the volume balance can be adjusted
between the 2 waves.
Press the [PAGEs] button and the follo wing display will appear.
10. Save the Voice You Have Created
Let’s save the drum voice you created to the DTXPRESS III’s
memory. Drum kit numbers “49” – “80” (these are called user
drum kits) are used for saving individual drum kits.
Press the [SAVE/ENT] button, the following display will ap-
pear.
Create Your Own Original Drum Kit
Use the [SEL<]/[SEL>] and [VALUE–]/[VALUE+] buttons
to select the layer number.
* If the assigned voice is not made of 2 layers this setting is
not valid.
Press the [SEL>] button to move the flashing cursor to the
layer balance position, then use the [VALUE–]/[VALUE+]
buttons to set the layer balance value.
8. Adjust the Amount of Reverb.
Let’s try and adjust the amount of reverb effect that is applied
to the voice.
Use the [PAGEs]/[PAGEt] buttons to select the display
shown below.
KIT*IN=snare V=1
LayerBalance=+20 Layer Balance
Layer Number
Use the [SEL<]/[SEL>] buttons to move the flashing cursor
to the reverb send level position, then use the [VALUE–]/
[VALUE+] buttons to set the value.
Large values will increase the amount of reverb applied to the
voice, “0” will produce no reverb.
* This setting is the reverb level for each input source. The
overall reverb level for the drum kit is set in [5-2. Drum Re-
verb Send] (Reference Guide : P. 24)
9. Adjust the Balance Between Layer 1 and 2.
If you have used a 2 layer voice in the voice you just created,
adjust the balance between the voices by adjusting the volume
of each voice.
* You can select the conversion curve for 2 voices. m
Drum Kit Edit Mode [2-1. Cross Fade] (Reference Guide : P. 20)
KIT*IN=snare
Reverb send= 40 Reverb send level
Use the [VALUE–]/[VALUE+] buttons to set the drum kit num-
ber (“49” – “80”) for saving your drum kit to.
Press the [SAVE/ENT] button, “Are you sure ?” will
appear on the display asking for confirmation.
* To cancel the save operation, press the [VALUE–] button.
Press the [SAVE/ENT] button again, the save operation will
be carried out, then “Complete!” will appear. After “Com-
plete!” appears, the display will return to the Drum Voice
select display.
11. Give Your Drum Kit a Name
The completed drum kit will still have the original drum kit’s
name.
Press the [VOICE] button to enter the Drum Kit Voice Edit
mode, then press the [PAGEt] button to display the Drum
Kit Name setting display shown below. With the same proce-
dure you used when you made a Song, give your drum kit an
original name. (P. 23)
Store Drumkit
=49 User Kit
Now the drum kit with the original snare drum
you created is complete.
Use the same procedure to create drum voices
for the other pads (input source) and create a
complete drum kit that is all your own.
The DTXPRESS III also has keyboard voices that comply
with the GM System Level 1. So, not only drum voices, but
piano, guitar, bass, strings, brass, reeds, effect, etc. can be
delivered when the pad is struck.
To use keyboard voices with the pads first, change the pad’ s
MIDI channel to any channel other than “10” (Reference
Guide : P. 19 [1-7. Channel, Gate Time]), then select the
MIDI note number of the voice you want to use in (Refer-
ence Guide : P. 19 [1-6. Note Number] )
* If the [2-5. Key Off Enable] (Reference Guide : P. 21) is set
to “disable”, some voices may sound continuously. In
this case, press the [SHIFT] + [VOICE] buttons to stop
voices sounding.
KIT Common
Kit=Acoustic Kit