Yamaha GX-90VCD RECORDING CD/VIDEO-CDSOURCES, To record programmed tracks from one or more discs, 3–6, number, on page, “PROG” and, SKIP button, Follow steps, Selected disc

Follow steps 3–6 on page 38.

RECORDING CD/VIDEO-CD SOURCES

1 9 1

To record programmed tracks from one or more discs

MINI COMPONENT SYSTEM GX–90VCD

VIDEO CD

Version 2.0 / Playback Control

1

2

DISC

PROGRAM

MUSIC

3

PRESET/TUNING

/BAND

CD

A/B/C/D/E

DISC CHANGE

OPEN/CLOSE

	DISPLAY
	EDIT
	REPEAT
RANDOM	VOLUME

1 Press the CD input selector button and load a disc (or discs) on the disc table.

2

3 Press the PROG button.

*“PROG” and “P-01” will light up on the display, and all track numbers on the selected disc will begin flashing.

4 If necessary, select a desired disc by pressing the DISC

ECHO	ECHO	INPUT	INPUT
USER	MEMORY	TAPE 1/2
	MODE	REC/PAUSE		NORMAL
					Active Servo
POWER	DOLBY NR			HIGH	Technology
	PHONES	TIMER REC		DUBBING	MIC MIXING
					MEMORY
	AUTO/MAN’L
	TIMER				TIME ADJ

			CD
	1	2	3	4	5
	1	2	3	4	5	5
	6	7	8	PRESET
	6	7	8	9	0
TIME	A	B	C	D	E
	TIME	PROG	TAPE	EDIT	+I0
3	MODE	INDEX	REPEAT OPEN/CLOSE TUNER
	DISC SKIP	PREV	NEXT	RETURN	SELECT
7	REC/PAUSE	TAPE 1/2	PLAY	STOP	PLAY	9
	CENTER/REAR	TEST	FLAT	TAPE
	/DELAY					1
4	ECHO/KEY		MUSIC	PROGRAM	USER
	LEVEL
	SLEEP		POWER		INPUT	1

VOLUME

Display information during programming

Selected disc

GRAM	USER	TAPE 1	1	2	3	4 5 6
HALL		B	7	8	9	10 11 12
			13 14 15 OVER 15

TRACK

PROG

A VOLUME

Next playback order Side of the tape

Programmed track numbers light up and unprogrammed ones flash.

		TAPE 1
RAM	USER			1		2	3	4 5 6
HALL		B			7	8	9	10 11 12
			REM 13 14 15 OVER 15

TRACK

PROG

A VOLUME

Selected track	Total remaining time on
number	the side of the tape

SKIP button.5 Select the desired track number by pressing the track number input buttons.

6 Repeat steps 4 and 5 to program more selections for the side A of the tape. You can select the same track again.

*Pressing the TIME button displays the total remaining time on the side of the tape for about 1 second, and then it is replaced by the display of the next playback order.

*If “TM OVER” appears on the display, the track number just selected cannot be programmed because there is not enough time remaining on the side A of the tape. However, at this time, if any other track number is flashing continuously on the display, you can program

it instead of the unprogrammable one.7 After you finish the programming for the side A, press the TAPE button.*“PU SET” appears on the display, then you can begin programming for side B.

*After this step is done, you can check the programmed contents for side A and side B alternately by pressing the TAPE button at any time before you press the EDIT button in step 9.

8 Repeat steps 4 and 5 to program selections for the side B of the tape. You can select the same track again.

*If “TM OVER” appears on the display, the track number just selected cannot be programmed because there is not enough time remaining on the side B of the tape. However, at this time, if any other track number is flashing continuously on the display, you can program

it instead of the unprogrammable one.

9 Press the EDIT button. (“EDIT” appears on the display.) The recording is automatically started.

Notes on tape-editing

•If programs are made selecting tracks from more than one disc, during recording, the DISC CHANGE button on the Video-CD player is disabled.

•To check, cancel or correct program data, refer to page•The maximum number of tracks that can be programmed is 20.•This function can be used to program up to track number

15.If the disc has more than 15 tracks, track number 16 and thereafter will not be programmed.

E-40