Using the built-in timer

STANDBY/ONINPUT

 

 

 

DISC1 DISC2 DISC3

 

 

 

 

DISC CHANGE

OPEN/CLOSE

3–DISC CD CHANGER

 

 

 

 

 

 

 

 

DIGITAL AUDIO

 

 

STANDBY

 

 

 

 

 

 

 

PROGRAM

B.BOOST

MUSIC

STANDBY

 

 

 

 

 

 

 

 

 

 

 

/ON

TIMER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VOLUME

 

 

 

INPUT

PRESET/TUNING/BAND

A/B/C/D/E

 

 

 

 

 

 

 

 

 

 

 

 

/

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UP

 

 

 

 

 

 

 

 

 

 

 

 

DOWN

 

 

 

 

 

BASS

TREBLE

 

REC/

AUTO/

 

 

 

 

 

 

 

 

PHONES

MODE

DOLBY NR

PAUSE

MANUAL

MEMORY

RANDOM

REPEAT

TIME

DISPLAY

 

 

 

 

 

 

TIMER

TIME ADJ

HOUR

MIN

 

 

 

 

TIMER MINHOUR DISPLAY

POWER

POWER

(standby/on)

1

2

3

1

2

3

4

5

6

4

5

6

7

8

9

7

8

+I0

0

TUNER

PRESET

 

PRESET

TIME

PROG

R.TIME

A

B

C

EDIT

DISC SKIP

MODE

D

 

E

 

CD

 

 

/

 

 

DIRECTION

 

REC/PAUSE

TAPE

TEST

 

— LEVEL

CENTER/

REAR/ DELAY

PROGRAM

 

MUSIC

SLEEP

 

INPUT

INPUT

VOLUME

Timer play

By using the built-in timer, you can set the time when this system turns on and a source play begins, and the time when this system is set to the standby mode.

1 Press DISPLAY.

Whenever DISPLAY is pressed, the display mode changes as follows.

→1 Current time (TIMER on/off mode)

↓

2Source selecting mode (TAPE, TUNER, CD)

↓

3ON TIME/Time setting mode

↓

4OFF TIME/Time setting mode

↓

5Normal display mode

Note

The display mode will change in about 8 seconds. If the mode is changed before the setting is completed, call the mode again by pressing DISPLAY once or more.

1Current time

Make sure that the current time is correct, and press TIMER so that “TIMER” lights up on the display.

2Source selecting mode

Select the source to be played with INPUT or (or INPUT on the remote control).

3ON TIME/time setting mode

[“ON TIME” appears on the display, and soon it is changed to a time setting mode.]

Set the time when you want to begin the timer play.

•Press HOUR and set the hour.

•Press MIN and set the minute.

4OFF TIME/time setting mode

If necessary, set the time when you want to finish the timer play in the same way as you did in step 3. If you do not set the time, it will be automatically set so that the timer play finishes after 1 hour.

2 Press TIMER to complete the timer play setting. This system turns into the standby mode.

* The STANDBY and TIMER indicators light up.

If you will continue using this system, press STANDBY/ON to turn on this system.

To cancel the timer play setting

Press DISPLAY, and then press TIMER so that the TIMER indicator goes out.

Note

Unless there is a power failure for more than 5 minutes, the set time will be retained until it is reset.

English

E-37