Yamaha PLG150-DX

MIDI Data Format

1.2.16 NRPN (Non-registered parameter number)

This is a message for setting the sound for things like vibrato, ﬁlter or EG. Use

NRPN MSB and NRPN LSB to specify the parameter that you wish to modify,

and then use Data Entry (see 1.2.4) to set the value for the speciﬁed parameter.

Control# Parameter Data Range

98 NRPN LSB 0...127

99 NPRN MSB 0...127

If the Multi Part parameter Rcv NRPN = OFF, that part will not receive NRPN.

The following NRPN messages can be received.

*1 See 1.2.4

*2 “--” means that the set value will be ignored.

*3 Adjusts the time after the note is played until vibrato begins to take effect. The effect

will begin more quickly for lower values, and more slowly for higher values.

1.2.17 RPN (Registered parameter number)

This message is used to specify part parameters such as Pitch Bend Sensitivity or

Tuning. Use RPN MSB and RPN LSB to specify the parameter that you wish to

modify, and then use Data Entry (see 1.2.4) to set the value of the speciﬁed

parameter.

Control# Parameter Data Range

100 RPN LSB 0 ... 127

101 RPN MSB 0 ... 127

If the Multi Part parameter Rcv RPN = OFF, that part will not receive this mes-

sage.

The following RPN messages can be received.

*1 Refer to 1.2.4

*2 “--” means that the set value will be ignored.

1.2.18 Assignable controller

By assigning a control change number of 0...95 to a part, application of effects

can be controlled. This device allows two control change numbers (AC1 and

AC2) to be speciﬁed for each part.

The following parameters specify the effect of AC1 and AC2:

* Multi Part Parameter

1. AC1, AC2 PITCH CONTROL

2. AC1, AC2 FILTER CONTROL

3. AC1, AC2 AMPLITUDE CONTROL

4. AC1, AC2 LFO PMOD DEPTH

5. AC1, AC2 LFO AMOD DEPTH

The AC1 control change number is speciﬁed by the Multi Part parameter ACl

CONTROLLER NUMBER, and the AC2 control change number is speciﬁed by

the Multi Part parameter AC2 CONTROLLER NUMBER.

1.3 Channel mode messages

These messages specify the basic operation of a part.

1.3.1 All Sound Off

This message silences all notes being played on the corresponding channel.

However, channel messages such as Note-on and Hold-on will be maintained in

their present state.

Control# Parameter Data Range

120 All Sound Off 0

1.3.2 Reset All Controllers

This message changes the settings of the following controllers.

The following data is not changed

Parameter values speciﬁed for program change, bank select MSB/LSB, volume,

pan, effect send levels 1, 3, 4, RPN and NRPN.

Control# Parameter Data Range

121 Reset All Controllers 0

1.3.3 All Note Off

This message turns off all notes which are currently on for the corresponding

part.

However, if Hold 1 or Sostenuto are on, notes will continue to sound until these

are turned off.

Control# Parameter Data Range

123 All Note Off 0

1.3.4 Omni Off

Works the same as when All Note Off is received.

Control# Parameter Data Range

124 Omni Off 0

1.3.5 Omni On

Works the same as when All Note Off is received.

Control# Parameter Data Range

125 Omni On 0

1.3.6 Mono

Works the same as when All Sound Off is received, and if the value (mono num-

ber) is in the range of 0... 16, sets the corresponding channel to Mode4* (m = 1).

Control# Parameter Data Range

126 Mono 0 ... 16

* Mode4 is a state in which only channel messages on the speciﬁed channel will

be received, and notes will be played individually (monophonically).

1.3.7 Poly

Works the same as when All Sound Off is received, and sets the corresponding

channel to Mode3*.

Control# Parameter Data Range

127 Poly 0

* Mode3 is when channel messages will be received only on the speciﬁed chan-

nel, and notes will be sounded polyphonically.

1.4 Program change

This message is used to switch voices.

It changes the program number on the receiving channel. When the change is to

include the voice bank, transmit the program change after sending the Bank

Select message (see 1.2.1).

If the Multi Part parameter Rcv PROGRAM CHANGE = OFF, that part will not

receive program changes.

NRPN

MSB LSB Data Entry*1

MSB LSB Parameter Name and Data Range

01H 08H mm --*2 Vibrato rate