Yamaha CDX-E400, RX-E400 manual

CRX-E400 RX-E400

CDX-E400

Receiver/CD Player

Récepteur/Lecteur CD

OWNER’S MANUAL MODE D’EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING

Contents

Page 7Do not plug in this unit to a wall outlet until all connections are complete 8Do not operate this unit upside-down.It may overheat, possibly causing damage 9Do not use excessive force on switches, knobs and/or cords 18VOLTAGE SELECTOR (General model only) CAUTION FOR CARRYING THE UNIT Remote control Connecting the speakers and antennas Connecting the system Setting the clock Adjusting the brightness of the display <RX-E400 • Remote control •Batteries (AA, R6, UM-3) •AM loop antenna •Indoor FM antenna Remote control operation range Receiver, RX-E400: p.8 CD player, CDX-E400: p.18 Right speaker 3 FM antenna Left speaker 2 AM loop antenna 4 To wall outlet 2 Connect RX-E400and CDX-E400with the system control cable The other SYSTEM CONNECTOR of CDX-E400is for connecting MDX-E300or KX-E300 3 Connect the AC power plug of CDX-E400to AC OUTLET of RX-E400 <RX-E400 Audio pin cable STANDBY/ON DISPLAY HOUR MIN PRESET/BAND 2 While the power is on, press DISPLAY to display the time 2 TIMER indicator (P.15) 0 PHONES (P.9) 3 DISPLAY (P.15) q Remote control sensor (P.3) 4 TIME ADJ/MEMORY (P.6/P.11) 2 Preset numbers (P.11) 3FREQ/RDS (P.12) 4PTY SEEK MODE (P.13/P.14) 5PTY SEEK START (P.13/P.14) 47 PRESET /(P.11) STANDBY/ ON BASS TREBLE BALANCE BASS: You can find radio stations automatically and manually 1 Follow steps 1 and 2 described in “Automatic tuning.” AUTO/MAN’L PRESET/TUNING 2 Press AUTO/MAN’L so that “AUTO” disappears from the display •Each time you press PRESET/TUNING or , the frequency changes step by step MEMORY PRESET/BAND 1 Tune in a desired station (Refer to the previous page for the tuning procedure.) 2 Press MEMORY 4 Press MEMORY The name of the RDS station being received is displayed PTY Current time is displayed PRESET 3 Press FREQ/RDS 3.Timer REC (Example) HOUR MIN TIMERINPUT 1 Press DISPLAY Page 1 STANDBY/ON (P.19) ^(Play/Pause) (P.19) 2 Disc tray (P.19) 6 Display (this page) (Open/Close) (P.19) $/!(Skip/Search Backward) 1 Numeric buttons (P.19) • +100 button is used when operating MDX-E300 2 REP (Repeat) (P.21) 3 RANDOM (Random) (P.20) 4 PROG (Program) (P.21) 3 Press to open the disc tray, and place a CD on the tray 4 Press ^to start play. This unit starts play To pause play Press ^ To resume play, press ^again TEXT/TIME Each time you press TEXT/TIME, the display changes as follows: Elapsed time of the current track Remaining time of the current track Total disc play time SINGLE REPEAT FULL REPEAT 1.Press &to stop program play 1.Follow the preceding procedure described in “To check program data.” 2.Display the track number to be changed by pressing When program play is stopped, press & MDX-E300 1 Numeric buttons 2 REP (Repeat) 3 RANDOM 4 TEXT/TIME Play unit Record unit DUBBING MODE Recording automatically starts from the beginning of the tape. (By pressing DUBBING START •The sound is automatically faded out when it gets close to the end of side B R.TIME SYMPTOM CAUSE REMEDY RX-E400 CDPLAYER CDX Amplifier section Tuner section CD player section Laser diode properties General CDX-E400 On the rear panel Printed in Malaysia