CONNECTIONS
■Connections
Be sure to connect the left channel (L), right channel (R), “+” (red) and
CAUTION
•Use speakers with the specified impedance shown on the rear panel of this unit.
•Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers.
10 mm (3/8”)
|
|
|
|
|
1 |
|
| 2 | |
| 4 |
Red: positive (+) | 3 |
| |
Black: negative |
|
| 5 |
Banana plug |
|
(With the exception of U.K. and Europe models)
A speaker cord is actually a pair of insulated cables running side by side. One cable is colored or shaped differently, perhaps with a stripe, groove or ridge.
1 Remove approximately 10 mm (3/8”) of insulation from each of the speaker cables.
2 Twist the exposed wires of the cable together to prevent short circuits.
3 Unscrew the knob.
4 Insert one bare wire into the hole in the side of each terminal.
5 Tighten the knob to secure the wire.
y
(With the exception of U.K. and Europe models)
•You can also use banana plug connectors. First, tighten the knob and then insert the banana plug connector into the end of the corresponding terminal.
■IMPEDANCE SELECTOR switch
WARNING
Do not change setting of the IMPEDANCE SELECTOR switch when the unit power is switched on, as doing so may damage the unit. If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR switch may not be fully slid to either position. If this is the case, slide the switch all the way to either position when this unit is in standby mode. Be sure to move this switch only when this unit is in standby mode.
Select the switch position (left or right) according to the impedance of the speakers in your system.
(General model)
|
|
|
| IMPEDANCE SELECTOR |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
| SET BEFORE POWER ON |
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MAIN A OR B : | 4ΩMIN. /SPEAKER | MAIN A OR B : | 8ΩMIN. /SPEAKER |
| ||||||||||||||
CENTER | A+B : | 8ΩMIN. /SPEAKER | CENTER | A+B : 16ΩMIN. /SPEAKER |
| |||||||||||||
: | 6ΩMIN. /SPEAKER | : | 8ΩMIN. /SPEAKER |
| ||||||||||||||
REAR CENTER: | 6ΩMIN. /SPEAKER | REAR CENTER: | 8ΩMIN. /SPEAKER |
| ||||||||||||||
REAR | : | 6ΩMIN. /SPEAKER | REAR | : | 8ΩMIN. /SPEAKER |
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IMPEDANCE SELECTOR switch
Switch | Speaker | Impedance level | |
position |
|
| |
|
|
| |
| Main | If you use one/two set(s) of main speakers, the impedance of | |
|
| each speaker must be 4 Ω/8 Ω or higher. | |
Left |
|
| |
Center, | The impedance of each speaker must be 6 Ω or higher. | ||
| |||
| Rear Center, |
| |
| Rear |
| |
|
|
| |
| Main* | If you use one/two set(s) of main speakers, the impedance of | |
|
| each speaker must be 8 Ω/16 Ω or higher. | |
Right |
|
| |
Center, | The impedance of each speaker must be 8 Ω or higher. | ||
| |||
| Rear Center, |
| |
| Rear |
| |
|
|
|
*[Canada model only]
When the switch is set to right, you cannot use “A+B”.
16
