Tuner, Remote control, English | Yamaha RX-V740 specification

■Tuner

TROUBLESHOOTING

■Tuner

	Problem	Cause	Remedy	Refer to
				page

	FM stereo reception is	The characteristics of FM stereo	Check the antenna connections.	13
	noisy.	broadcasts may cause this problem	Try using a high-quality directional FM
		when the transmitter is too far away or	antenna.
		the antenna input is poor.
		the antenna input is poor.	Use the manual tuning method.	33
			Use the manual tuning method.	33

	There is distortion, and	There is multipath interference.	Adjust the antenna position to eliminate	–
	clear reception cannot		multipath interference.
FM	be obtained even with a
	good FM antenna.

	The desired station	The station is too weak.	Use a high-quality directional FM antenna.	–
	cannot be tuned in with	The station is too weak.	Use a high-quality directional FM antenna.	–
	cannot be tuned in with
	the automatic tuning		Use the manual tuning method.	33
	method.		Use the manual tuning method.	33
	method.

	Previously preset	The unit has been disconnected for a	Re-store the stations.	34
	stations can no longer	The unit has been disconnected for a	Re-store the stations.	34
	stations can no longer	long period.
	be tuned in.	long period.
	be tuned in.

	The desired station	The signal is weak or the antenna	Tighten the AM loop antenna connections and	–
	cannot be tuned in with	connections are loose.	orient it for best reception.
	the automatic tuning
	the automatic tuning
	method.		Use the manual tuning method.	33

AM	There are continuous	Noises result from lightning,	Use an outdoor antenna and a ground wire.	13
AM	crackling and hissing	fluorescent lamps, motors, thermostats	This will help somewhat, but it is difficult to
	crackling and hissing	fluorescent lamps, motors, thermostats	This will help somewhat, but it is difficult to
	noises.	and other electrical equipment.	eliminate all noise.

	There are buzzing and	A TV set is being used nearby.	Move this unit away from the TV.	–
	whining noises
	(especially in the
	evening).

■ Remote control

Problem	Cause	Remedy	Refer to
			page

The remote control does	Wrong distance or angle.	The remote control will function within a	7
not work nor function		maximum range of 6 m (20 feet) and no more
properly.		than 30 degrees off-axis from the front panel.

	Direct sunlight or lighting (from an	Reposition this unit.	–
	inverter type of fluorescent lamp, etc.) is
	striking the remote control sensor of this
	unit.

	The batteries are weak.	Replace all batteries with new ones.	3

	The manufacture code has not correctly	Set the code correctly.	47
	set.
	set.	Try setting another code of the same manufac-	47
		Try setting another code of the same manufac-	47
		turer.

	Even if the manufacturer code is correctly		–
	set, there are some models that do not		–
	set, there are some models that do not
	respond to the remote control.

INFORMATION	ADDITIONAL

English

63

Image 67

Yamaha RX-V740 owner manual Tuner, Remote control, English

Contents

AV Receiver RX-V740 IMPORTANT SAFETY INSTRUCTIONS I CAUTION Note to CATV system installer FCC INFORMATION for US customers We Want You Listening For A Lifetime CAUTION READ THIS BEFORE OPERATING YOUR UNITIII CAUTION ADDITIONAL INFORMATION CONTENTSINTRODUCTION BASIC OPERATION About this manual FEATURES control Supplied accessoriesInstalling batteries in the remote GETTING STARTED Front panel CONTROLS AND FUNCTIONSa s d f wSILENT PHONES jack INTRODUCTION English Remote control iAMP Using the remote controlHandling the remote control uSELECT k/n y u i o p a Front panel display~~~~~~~~~~~~~~ 0 q w e English Before connecting componentsConnecting to digital jacks CONNECTIONS Connecting a recording component Connecting video componentsConnecting a video monitor Connecting a DVD player/digital TV/cable TV TV/digital TV cable TV VCR indicates audio signal directionEnglish DVD player Connecting a turntable Connecting audio componentsConnecting a CD player Connecting a CD recorder or MD recorder Connecting the AM loop antenna Connecting the antennasEnglish Connecting an external amplifier Connecting an external decoder English Connecting the speakersSpeaker placement Speakers Connections IMPEDANCE SELECTOR switch REAR CENTER SPEAKER terminals MAIN SPEAKERS terminalsREAR SPEAKERS terminals CENTER SPEAKER terminals AC OUTLETS SWITCHED Connecting the power supply cordsTurning on the power Connecting the AC power cord Selecting the OSD mode ON-SCREENDISPLAY OSDP01 CONCERT HALL OSD modes Exit BASIC SYSTEM SETTINGSUsing the basic menu 1 SETUP 2 SP LEVEL 1 SETUPCANCEL4 SET/CANCEL SET MENU Setting speaker output levels SP LEVEL Setting the unit to match your speaker system AUTO PLAYBACK Night listening mode When you have finished using this unitBGV background video function To mute the sound Notes on playing DTS-CD/LDs Notes on digital signalsInput modes and indications AUTO PLAYBACK AdventureGeneral Selecting a sound field program Playing Dolby Digital EX or DTS ES material PRO LOGICMatrix Selecting PRO LOGIC, PRO LOGIC II or Neo6 SILENT CINEMA DSP Virtual CINEMA DSPNormal stereo reproduction Recreating a sound field DIGITAL SOUND FIELD PROCESSING DSPUnderstanding sound fields Hi-FiDSP programs For audio-videosources No. 4 to CINEMA-DSPSound design of CINEMA-DSP CINEMA-DSPPrograms Straight Decode For movie programsEnglish Dolby Pro Logic + DSP sound field effect Sound field effectsDolby Digital/DTS + DSP sound field effect Dolby Digital EX/DTS-ES+ DSP sound field effect AAM 1530 kHz TUNINGAutomatic tuning Manual tuning Automatically presetting stations for FM stations Presetting stationsA1 FM 89.9 MHz C3 AM 1440 kHz Manually presetting stationsAAM 1440 kHz C AM 1440 kHz A5 FM 90.6 MHz Selecting a preset stationExchanging preset stations E1 FM 87.5 MHz SLEEP 120min L R SLEEP TIMERSetting the sleep timer Canceling the sleep timer RECORDING Special considerations when recordingDTS material 3,5,8 Adjusting the items on the set menuSET MENU Set menu list 1A CENTER center speaker mode SOUND 1 SPEAKER SET speaker mode settings 1E BASS bass out mode 1B MAIN main speaker mode1C REAR LR rear speaker mode 1D REAR CT rear center speaker mode SOUND 3 LFE LEVEL Setting by “meters”Setting by “feet” SOUND 2 SP DISTANCE speaker distance 1A for COMPONENT VIDEO INPUT jacks SOUND 5 CENTER GEQ center graphic equalizerSOUND 6 HP TONE CTRL INPUT 1 I/O ASSIGN input output assignment 3 INPUT RENAME INPUT 2 INPUT MODE initial input modeINPUT 3 INPUT RENAME OPTION 1 DISPLAY SET OPTION 5 REC OUT OPTION 2 MEM. GUARD memory guardOPTION 3 AUDIO MUTE OPTION 4 ZONE SET Controlling other component REMOTE CONTROL FEATURESControl area Controlling this unit English Setting the manufacturer code Changing the source name in the display window Clearing renamed source names and setup manufacturer codesEnglish 9 0 q w e Controlling other components English SETTING THE SPEAKER LEVELSAdjusting the volume during playback Using the test tone ZONE 2 For U.S.A., Canada and Australia models To enable Zone 2 mode When you have finished using the unit Remote Control in ZoneTo enable Zone 2 mode on the remote control To use the remote control in Zone Sound field program parameters What is a sound field?SOUND FIELD PROGRAM PARAMETER EDITING Elements of a sound field P03 ROCK CONCERT Changing parameter settingsEnglish P. INT. DLY for the presence sound field Digital Sound Field Parameter DescriptionsDSP LEVEL INIT. DLY Initial delay S. LIVENESS Surround liveness LIVENESSS. INIT. DLY Surround initial delay S. ROOM SIZE Surround room size REV. DELAY Reverberation delay REV. TIME Reverberation timeREV. LEVEL Reverberation level RR LEVEL Rear right level DIMENSIONFor 6ch Stereo CT LEVEL Center level RL LEVEL Rear left level General TROUBLESHOOTING page English Refer to Tuner Remote controlEnglish Dolby Pro Logic GLOSSARYDolby Surround Dolby Digital Sampling frequency and number of quantized bits S-videosignalComponent video signal PCM Linear PCM FM SECTION SPECIFICATIONSAUDIO SECTION VIDEO SECTION WA69310