Yamaha TX4n, TX5n 3. , 4.

TX6n/5n/4n Reference Manual 25

Panel Operations

3. Use encoder A to move the cursor to the parameter that you want to edit, and encoder B to edit the parameter

value.

4. If the parameter value is blinking, press the [ENTER] button to conﬁrm the value.

Non-blinking parameter values are reﬂected by the ampliﬁer in real time.

■General

Here you can make general settings for the ampliﬁer, such as gain/input sensitivity and amp mode.

●Sensitivity/Amp Gain

●Stereo/Bridge/Parallel

●Attenuation Link

Parameter name Range Explanation

Amp Gain 19.8–43.8 dB Speciﬁes the gain of each channel. The gain and input sensitivity are

linked; you may edit either one.

Sensitivity TX6n: 24.0–0.0 dBu

TX5n: 22.6– -1.4 dBu

TX4n: 21.4– -2.6 dBu

Speciﬁes the input sensitivity of each channel. Since the maximum out-

put is different for each model, the settable range will differ for each

model. The gain and input sensitivity are linked; you may edit either

one.

Gain Mode Link ON/OFF Speciﬁes whether the gain and input sensitivity settings will be linked

between channels.

Standby/On Standby/On Switches the power between Standby and On modes. Standby is a

state in which the speaker output’s power amp section is off (operation

other than speaker output will continue).

Parameter name Range Explanation

Amp Mode Stereo The ampliﬁer will operate in stereo, with channels A and B indepen-

dent.

Bridge The ampliﬁer will operate as a monaural high-power ampliﬁer that

bridge-connects the speaker output’s power amp sections, with the out-

put signal from the channel A speaker processor as the source.

Parallel The ampliﬁer will operate as a two-channel monaural ampliﬁer, with the

output signal from the channel A speaker processor as the source.

Parameter name Range Explanation

Att Link ON/OFF Speciﬁes whether the attenuator settings will be linked between chan-

nels.

Contents

Main Contents Introduction............................................. 3 Controls and Connectors ......................5 Panel Operations.................................. 12 System Connection Examples ............44 Introduction About the documentation Setup Terms Controls and Connectors Front Panel t[PROTECTION] indicator y[BRIDGE] indicator u[PARALLEL] indicator i[MUTE] indicator o[MUTE] button !3 Encoders A, B !4 Display !5 Function buttons !6 [HOME] button !7 [EXIT] button Rear Panel @2@1 @4 @5 @3@7 @6 @4 [NETWORK] connector @5 [FAULT OUTPUT] connectors Optional I/O cards Page Page Panel Operations About the Display Switching Screens Editing the Parameters Adjusting the Attenuation Screen Structure METER SETTING SCENE Screen LIB. UTILITY Operations that can be Performed from the Panel Alert Messages HOME Screen Meter types that can be shown METER Screen Page Parameters that can be edited The parameters that can be edited will depend on the meter type. 1. 2. 3. 4. Device Setup UTILITY Screen 1. 2. Information Here you can specify the IP address and other settings for using the amplier in a network. Network Setup LCD Setup Front Panel Operation Setting the Lock 1. 2. Temporarily defeating panel lock 1. 2. Scene Setup Misc Setup 1. 2. MENU Screen 3. value. Attenuation Link 4. Non-blinking parameter values are reected by the amplier in real time. Signal Path When digital input signal becomes unlocked in Backup mode detected in Override mode Signal Chain Analog Input Signal Chain/Slot Input Signal Chain Output Signal Chain Calibration Calibrate by Pilot Tone This performs the measurements using a pilot tone generated by the amp. Calibrate by Prog Source Limiter Here you can specify the limiter conditions for the amplier. Limiter Gain Reduction Voltage Limiter These settings specify how the limiter will be controlled by the output voltage. SIGNAL PATH Screen NOTE Page Page Slot Input Router Here you can specify the routing and gain from the slot input to each input channel. This is a 4-input 4-output mixer with the input channels and output channels arranged in a matrix. Input On/Off Here you can turn the input to the 4x4 Matrix Mixer on/off for each input channel. 8Band Input EQ Here you can specify a delay for the signal. Input Delay Oscillator Mix This species the phase reversal of the input signal to the crossover. X-Over Input Level (Speaker Processor) This adjusts the input level to the crossover in a range of - +10 dB. X-Over Polarity (Speaker Processor) X-Over (Speaker Processor) Output Delay (Speaker Processor) Here you can specify a delay for the signal. 6Band Output EQ (Speaker Processor) Filter types Output Level (Speaker Processor) Mute On/Off (Speaker Processor) Limiter (Speaker Processor) Output Router Recalling a scene 1. 2. 3. 4. SCENE Screen Page Page 1. 2. 3. Initializing the internal memory System Connection Examples Mixer Daisy-chain connection via analog or digital audio Thru-output for digital connections Regarding digital connections Redundant connections (Backup) TX6n/5n/4n Reference Manual 47 EX ES64 You can connect up to three MY16-EX I/O expansion cards to a single MY16-ES64 card. EtherSound connections Bridge connections from EtherSound to AES/EBU CobraNet connections Bridge connections from CobraNet to AES/EBU Connecting External Controllers and Analog Devices Example : Using an LED to indicate normal/fault status of the TXn Remote control from AMX or Crestron ([NETWORK] connector) Controlling an analog device ([FAULT OUTPUT] connector) Connecting External Controllers and Analog Devices 1. 2. 3. 4. Euroblock plug connection Cable preparation Adjusting the Input/Output Levels Initial setting ATT: -dB GAIN: 32.0dB (default) TX5n Clips TX4n Clips Adjusting the input/output levels Appendix Messages that may appear in the TXns display and the appropriate responses are listed below. Message List Alert Message List (Excerpt) Troubleshooting Index Numerics A B C L M N O P