Manuals / Brands / Home Audio / Stereo Amplifier / Yamaha / Home Audio / Stereo Amplifier

Yamaha TX4n, TX5n Output Delay (Speaker Processor), 6Band Output EQ (Speaker Processor)

1 60

Download 60 pages, 1.31 Mb

TX6n/5n/4n Reference Manual 37

Panel Operations

■Output Delay (Speaker Processor)

Here you can specify a delay for the signal.

■6Band Output EQ (Speaker Processor)

This is a six-band parametric equalizer that boosts or cuts the signal at the speciﬁed frequencies. For each channel, you can

make settings for each frequency band (BAND A–F).

Parameter name Range Explanation

On ON/OFF Turns the delay on/off.

Delay Time 0.00–500.00 ms Speciﬁes the delay time.

Parameter name Range Explanation

Type PEQ, L.SHELF 6,

L.SHELF 12,

H SHELF 6,

H SHELF 12,

HPF, LPF, APF 1st,

APF 2nd, Horn EQ

Selects the ﬁlter type.

Q 63.0–0.10 Speciﬁes the width of each frequency band.

Frequency 20.0 Hz–20.0 kHz Speciﬁes the center frequency of each frequency band.

Gain -18.0–+18.0 dB Speciﬁes the gain for each frequency band.

Bypass ON/OFF Turns bypass on/off for each frequency band.

EQ All Bands ON/OFF Turns the entire six-band equalizer on/off.

Contents

Main Contents Introduction............................................. 3 Controls and Connectors ......................5 Panel Operations.................................. 12 System Connection Examples ............44 Introduction About the documentation Setup Terms Controls and Connectors Front Panel t[PROTECTION] indicator y[BRIDGE] indicator u[PARALLEL] indicator i[MUTE] indicator o[MUTE] button !3 Encoders A, B !4 Display !5 Function buttons !6 [HOME] button !7 [EXIT] button Rear Panel @2@1 @4 @5 @3@7 @6 @4 [NETWORK] connector @5 [FAULT OUTPUT] connectors Optional I/O cards Page Page Panel Operations About the Display Switching Screens Editing the Parameters Adjusting the Attenuation Screen Structure METER SETTING SCENE Screen LIB. UTILITY Operations that can be Performed from the Panel Alert Messages HOME Screen Meter types that can be shown METER Screen Page Parameters that can be edited The parameters that can be edited will depend on the meter type. 1. 2. 3. 4. Device Setup UTILITY Screen 1. 2. Information Here you can specify the IP address and other settings for using the amplier in a network. Network Setup LCD Setup Front Panel Operation Setting the Lock 1. 2. Temporarily defeating panel lock 1. 2. Scene Setup Misc Setup 1. 2. MENU Screen 3. value. Attenuation Link 4. Non-blinking parameter values are reected by the amplier in real time. Signal Path When digital input signal becomes unlocked in Backup mode detected in Override mode Signal Chain Analog Input Signal Chain/Slot Input Signal Chain Output Signal Chain Calibration Calibrate by Pilot Tone This performs the measurements using a pilot tone generated by the amp. Calibrate by Prog Source Limiter Here you can specify the limiter conditions for the amplier. Limiter Gain Reduction Voltage Limiter These settings specify how the limiter will be controlled by the output voltage. SIGNAL PATH Screen NOTE Page Page Slot Input Router Here you can specify the routing and gain from the slot input to each input channel. This is a 4-input 4-output mixer with the input channels and output channels arranged in a matrix. Input On/Off Here you can turn the input to the 4x4 Matrix Mixer on/off for each input channel. 8Band Input EQ Here you can specify a delay for the signal. Input Delay Oscillator Mix This species the phase reversal of the input signal to the crossover. X-Over Input Level (Speaker Processor) This adjusts the input level to the crossover in a range of - +10 dB. X-Over Polarity (Speaker Processor) X-Over (Speaker Processor) Output Delay (Speaker Processor) Here you can specify a delay for the signal. 6Band Output EQ (Speaker Processor) Filter types Output Level (Speaker Processor) Mute On/Off (Speaker Processor) Limiter (Speaker Processor) Output Router Recalling a scene 1. 2. 3. 4. SCENE Screen Page Page 1. 2. 3. Initializing the internal memory System Connection Examples Mixer Daisy-chain connection via analog or digital audio Thru-output for digital connections Regarding digital connections Redundant connections (Backup) TX6n/5n/4n Reference Manual 47 EX ES64 You can connect up to three MY16-EX I/O expansion cards to a single MY16-ES64 card. EtherSound connections Bridge connections from EtherSound to AES/EBU CobraNet connections Bridge connections from CobraNet to AES/EBU Connecting External Controllers and Analog Devices Example : Using an LED to indicate normal/fault status of the TXn Remote control from AMX or Crestron ([NETWORK] connector) Controlling an analog device ([FAULT OUTPUT] connector) Connecting External Controllers and Analog Devices 1. 2. 3. 4. Euroblock plug connection Cable preparation Adjusting the Input/Output Levels Initial setting ATT: -dB GAIN: 32.0dB (default) TX5n Clips TX4n Clips Adjusting the input/output levels Appendix Messages that may appear in the TXns display and the appropriate responses are listed below. Message List Alert Message List (Excerpt) Troubleshooting Index Numerics A B C L M N O P