Yamaha TX4n, TX5n

TX6n/5n/4n Reference Manual 17

Panel Operations

For each meter type, this screen lets you specify various parameters for alert detection, peak hold, and display

units.

●Setting procedure

1. In the HOME screen, press the left-most function button (METER) to access the METER screen.

2. Use the function buttons (PREV/NEXT) to access the screen for the meter whose settings you want to change.

3. Press the second-from-right function button (SETTING) to access the SETTING screen for that meter.

4. Press the second-from-left function button (CH A/B or CH 1/2) to access the settings for the channel that you

want to edit.

5. Use encoder A to move the cursor to the parameter that you want to edit, and encoder B to edit the parameter

value.

The edited parameter value will be reﬂected by the ampliﬁer in real time.

SETTING Screen

Channel whose settings you will edit

Contents

Main Contents Introduction............................................. 3 Controls and Connectors ......................5 Panel Operations.................................. 12 System Connection Examples ............44 Introduction About the documentation Setup Terms Controls and Connectors Front Panel t[PROTECTION] indicator y[BRIDGE] indicator u[PARALLEL] indicator i[MUTE] indicator o[MUTE] button !3 Encoders A, B !4 Display !5 Function buttons !6 [HOME] button !7 [EXIT] button Rear Panel @2@1 @4 @5 @3@7 @6 @4 [NETWORK] connector @5 [FAULT OUTPUT] connectors Optional I/O cards Page Page Panel Operations About the Display Switching Screens Editing the Parameters Adjusting the Attenuation Screen Structure METER SETTING SCENE Screen LIB. UTILITY Operations that can be Performed from the Panel Alert Messages HOME Screen Meter types that can be shown METER Screen Page Parameters that can be edited The parameters that can be edited will depend on the meter type. 1. 2. 3. 4. Device Setup UTILITY Screen 1. 2. Information Here you can specify the IP address and other settings for using the amplier in a network. Network Setup LCD Setup Front Panel Operation Setting the Lock 1. 2. Temporarily defeating panel lock 1. 2. Scene Setup Misc Setup 1. 2. MENU Screen 3. value. Attenuation Link 4. Non-blinking parameter values are reected by the amplier in real time. Signal Path When digital input signal becomes unlocked in Backup mode detected in Override mode Signal Chain Analog Input Signal Chain/Slot Input Signal Chain Output Signal Chain Calibration Calibrate by Pilot Tone This performs the measurements using a pilot tone generated by the amp. Calibrate by Prog Source Limiter Here you can specify the limiter conditions for the amplier. Limiter Gain Reduction Voltage Limiter These settings specify how the limiter will be controlled by the output voltage. SIGNAL PATH Screen NOTE Page Page Slot Input Router Here you can specify the routing and gain from the slot input to each input channel. This is a 4-input 4-output mixer with the input channels and output channels arranged in a matrix. Input On/Off Here you can turn the input to the 4x4 Matrix Mixer on/off for each input channel. 8Band Input EQ Here you can specify a delay for the signal. Input Delay Oscillator Mix This species the phase reversal of the input signal to the crossover. X-Over Input Level (Speaker Processor) This adjusts the input level to the crossover in a range of - +10 dB. X-Over Polarity (Speaker Processor) X-Over (Speaker Processor) Output Delay (Speaker Processor) Here you can specify a delay for the signal. 6Band Output EQ (Speaker Processor) Filter types Output Level (Speaker Processor) Mute On/Off (Speaker Processor) Limiter (Speaker Processor) Output Router Recalling a scene 1. 2. 3. 4. SCENE Screen Page Page 1. 2. 3. Initializing the internal memory System Connection Examples Mixer Daisy-chain connection via analog or digital audio Thru-output for digital connections Regarding digital connections Redundant connections (Backup) TX6n/5n/4n Reference Manual 47 EX ES64 You can connect up to three MY16-EX I/O expansion cards to a single MY16-ES64 card. EtherSound connections Bridge connections from EtherSound to AES/EBU CobraNet connections Bridge connections from CobraNet to AES/EBU Connecting External Controllers and Analog Devices Example : Using an LED to indicate normal/fault status of the TXn Remote control from AMX or Crestron ([NETWORK] connector) Controlling an analog device ([FAULT OUTPUT] connector) Connecting External Controllers and Analog Devices 1. 2. 3. 4. Euroblock plug connection Cable preparation Adjusting the Input/Output Levels Initial setting ATT: -dB GAIN: 32.0dB (default) TX5n Clips TX4n Clips Adjusting the input/output levels Appendix Messages that may appear in the TXns display and the appropriate responses are listed below. Message List Alert Message List (Excerpt) Troubleshooting Index Numerics A B C L M N O P