Auger Control Test

IMPORTANT: Perform the following test before operating your snow thrower for the first time and at the start of each winter season.

Check the adjustment of the auger control as follows:

When the auger control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.

In a well-ventilated area, start the snow thrower engine as instructed earlier in this section under the heading Starting the Engine. Make sure the throttle is set in the FAST position.

While standing in the operator’s position (behind the snow thrower), engage the auger.

Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times.

With the throttle control in the FAST (rabbit) position and the auger control in the disengaged “up” position, walk to the front of the machine.

Confirm that the auger has completely stopped rotating and shows NO signs of motion.

IMPORTANT: If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for ALL moving parts to stop before re-adjusting the auger control.

To readjust the control cable, loosen the hex jam nut on the auger control cable “Z” fitting.

Rotate the coupling end of the cable (without turning the cable) counterclockwise to provide more slack.

Retighten the hex jam nut. See Figure 11.

Repeat Auger Control Test to verify proper adjustment has been achieved.

To Throw Snow

CAUTION: Check the area to be cleared for foreign objects. Remove, if any.

1.Start the engine following starting instructions.

2.Rotate the discharge chute to the desired position, (away from bystanders and/or buildings) by moving the chute control.

3.Select the speed according to snow condition.

CAUTION: Never move the shift lever without first releasing the drive clutch.

4.Engage the auger control and drive control levers as previously stated.

Z Fitting

Hex Nut

Cable Should

Be Straight

Figure 11

5.The interlock feature will allow you to remove your left hand from the auger control lever.

6.When clearing the first pass through the snow, control speed of snow thrower according to the depth and condition of snow.

7.On each succeeding pass, readjust the chute to the desired positon and slightly overlap previous path.

8.After the area is cleared, stop the snow thrower following instructions given below.

Operating Tips

NOTE: Allow the engine to warm up for a few minutes as the engine will not develop full power until it reaches operating temperature.

WARNING: The temperature of muffler and

surrounding areas may exceed 150o F. Avoid these areas.

For most efficient snow removal, remove snow immediately after it falls.

Discharge snow downwind whenever possible. Slightly overlap each previous swath.

Set the skid shoes 1/4" below the scraper bar for normal usage. The skid shoes may be adjusted upward for hard-packed snow.

NOTE: It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing an injury or damage to the snow thrower.

If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the highest position for maximum clearance between ground and shave plate.

Clean the snow thrower thoroughly after each use.

12

Page 12
Image 12
Yard-Man 600 manual To Throw Snow, Operating Tips

600 specifications

The Yard-Man 600 is an innovative lawn mower that has gained a strong reputation for its efficiency, durability, and user-friendly features. Designed for both residential and commercial use, this mower provides an exceptional mowing experience, effortlessly tackling various terrains and grass types.

One of the standout features of the Yard-Man 600 is its powerful engine. Equipped with a robust 160cc OHV engine, it delivers reliable performance and superior cutting power. This engine allows the mower to handle thicker grass and uneven terrains while ensuring a consistent cutting height. The mower's self-propelled capability further enhances its efficiency, allowing users to navigate their yards with minimal effort.

The Yard-Man 600 boasts a durable steel deck that measures 21 inches, providing ample cutting width for mowing larger lawns with fewer passes. The steel construction not only ensures longevity but also contributes to the mower's stability and resistance to wear and tear. Additionally, the mower features a 5-position height adjustment system, enabling users to customize cutting heights from 1 to 4 inches, catering to different lawn conditions and personal preferences.

Another notable technology incorporated into the Yard-Man 600 is its advanced mulching system. This feature allows grass clippings to be finely shredded and returned to the lawn, promoting healthier soil and reducing yard waste. The mower also offers the option for side discharge and rear bagging, providing versatility based on user preference and lawn care needs.

Comfort and ease of operation are key priorities for the Yard-Man 600. It features an ergonomically designed handle that can be adjusted to multiple heights, ensuring a comfortable grip for users of different sizes. The mower's lightweight construction also makes it easy to maneuver, reducing fatigue during extended use.

Safety is paramount, and the Yard-Man 600 includes several safety features. It features a blade brake that stops the blade within seconds when the user releases the handle, minimizing the risk of accidents. Additionally, the sturdy wheel design provides excellent traction, contributing to safer operation on inclines and wet surfaces.

In conclusion, the Yard-Man 600 is an exceptional lawn mower that combines power, durability, and user-friendliness. With its powerful engine, versatile cutting options, and emphasis on safety, it stands out as a reliable choice for anyone looking to maintain a immaculate lawn. Whether you're a homeowner or a landscape professional, the Yard-Man 600 is engineered to meet and exceed expectations.