•Push idler away from the chute and insert a Philips head screwdriver in the hole on the idler as shown in Figure 26. This will release tension on drive belt.

Engine

Auger Belt

 

Pulley

 

Drive Belt

Idler

Figure 26

•Pull drive belt out and away from the engine pulley to remove. See Figure 26.

•Tip the snow thrower up and forward, so that it rests on the housing. Remove two self-tapping screws from frame cover underneath the snow thrower and move the frame cover away. Refer to Figure 24.

•Back out the stop bolt to create sufficient gap between the friction wheel disc and the drive pulley. Pull the drive belt from around the drive pulley and clear it off the friction wheel disc. See Figure 27.

Drive

Friction

Belt

Wheel

 

Drive Pulley

Stop

Bolt

Figure 27

•Now moving to the other side of the snow thrower , slide the belt off the crankshaft.

•Replace with new belt, first sliding it through the crank shaft, then working it around the groove of the drive pulley and finally wrapping it around the engine pulley from where the old belt was removed. Once the belt is firmly placed on the pulleys, make sure to remove the screwdriver from the idler.

•Re-install auger belt on the engine pulley.

•Re-attach frame cover and put the equipment back to operating position. Re-attach belt cover with two self-tapping screws removed earlier.

Friction Wheel Rubber

•Check the rubber on the friction wheel after 25 hours of operation, and periodically thereafter. Replace the rubber if any signs of wear or cracking are found.

•Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.

•Move shift lever to the R2 position.

•Tip the snow thrower so that it rests on the housing.

•Remove two self-tapping screws from frame cover underneath the snow thrower and move the frame cover away. See Figure 24.

•Remove the right-hand wheel by removing the screw and bell washer which secure it to the axle.

•Locate the hex shaft and snap ring on the right side of the snow thrower frame, about two inches from the wheel axle.

•Using a suitable tool, carefully remove the outer E- ring which secures the hex shaft to the snow thrower frame and lightly tap the shaft’s end to dislodge the ball bearing from the right side of the frame.

•Slide the hex shaft downward and to the left while carefully un-meshing the lower gears on the hex shaft from the upper gears on the wheel axle. See Figure 28.

•Set the hex shaft’s gears aside.

•Carefully remove the inner E-ring from the hex shaft and slide the friction wheel assembly off the hex shaft.

NOTE: If you’re replacing the friction wheel assembly as a whole, discard the worn part and slide the new part onto the hex shaft. Follow the steps above in reverse order to reassemble components. If you’re disassembling the friction wheel and replacing only the rubber ring, proceed as follows:

•Remove the four screws from the friction wheel assembly and remove the bonded friction wheel.

•Reassemble new bonded friction wheel rubber to the friction wheel assembly, turn each screw approximately 2 turns in order shown in Figure 29 until screws are tight. It is important for the rubber to be assembled symmetrically.

•Slide the friction wheel assembly back onto the hex shaft and follow the steps above in revers order to reassemble components.

18

Page 17 Page 19
Page 18
Image 18
Yard-Man 600 manual Friction Wheel Rubber
Page 17 Page 19

600 specifications

The Yard-Man 600 is an innovative lawn mower that has gained a strong reputation for its efficiency, durability, and user-friendly features. Designed for both residential and commercial use, this mower provides an exceptional mowing experience, effortlessly tackling various terrains and grass types.

One of the standout features of the Yard-Man 600 is its powerful engine. Equipped with a robust 160cc OHV engine, it delivers reliable performance and superior cutting power. This engine allows the mower to handle thicker grass and uneven terrains while ensuring a consistent cutting height. The mower's self-propelled capability further enhances its efficiency, allowing users to navigate their yards with minimal effort.

The Yard-Man 600 boasts a durable steel deck that measures 21 inches, providing ample cutting width for mowing larger lawns with fewer passes. The steel construction not only ensures longevity but also contributes to the mower's stability and resistance to wear and tear. Additionally, the mower features a 5-position height adjustment system, enabling users to customize cutting heights from 1 to 4 inches, catering to different lawn conditions and personal preferences.

Another notable technology incorporated into the Yard-Man 600 is its advanced mulching system. This feature allows grass clippings to be finely shredded and returned to the lawn, promoting healthier soil and reducing yard waste. The mower also offers the option for side discharge and rear bagging, providing versatility based on user preference and lawn care needs.

Comfort and ease of operation are key priorities for the Yard-Man 600. It features an ergonomically designed handle that can be adjusted to multiple heights, ensuring a comfortable grip for users of different sizes. The mower's lightweight construction also makes it easy to maneuver, reducing fatigue during extended use.

Safety is paramount, and the Yard-Man 600 includes several safety features. It features a blade brake that stops the blade within seconds when the user releases the handle, minimizing the risk of accidents. Additionally, the sturdy wheel design provides excellent traction, contributing to safer operation on inclines and wet surfaces.

In conclusion, the Yard-Man 600 is an exceptional lawn mower that combines power, durability, and user-friendliness. With its powerful engine, versatile cutting options, and emphasis on safety, it stands out as a reliable choice for anyone looking to maintain a immaculate lawn. Whether you're a homeowner or a landscape professional, the Yard-Man 600 is engineered to meet and exceed expectations.
Top Page Image Contents