Manuals / Yazoo/Kees / Lawn and Garden / Lawn Mower

Yazoo/Kees ZCBI48181 REPLACING BATTERY See Fig, To Attach Jumper Cables, Service And Adjustment

Models: ZCBI48181

1 40

Download 40 pages 29.62 Kb

Page 31

TO ATTACH JUMPER CABLES

SERVICE AND ADJUSTMENT

TO ATTACH JUMPER CABLES

•Connect each end of the RED cable to the POSITIVE (+) terminal on each battery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of the fully charged battery.

•Connect the other end of the BLACK cable to a good CHASSIS GROUND, away from the fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

REPLACING BATTERY (See Fig. 18)

WARNING

Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal brace- lets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift Seat and rotate forward.

•Open terminal access doors.

•Using two 1/2" wrenches disconnect BLACK battery cable then RED battery cable.

•Using 7/16" wrench, remove terminal guard.

•Carefully remove the battery from the mower.

•Install new battery with terminals in the same position as the old battery.

•Reinstall terminal guard

•First connect RED battery cable to positive (+) battery terminal with hex bolt and hex nut.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and hex nut.

•Tighten securely.

•Close terminal access doors.

•Lower seat.

TERMINAL
GUARD
	TERMINAL
	ACCESS
	DOORS
FIGURE 18	CZ-22
FIGURE 18

31

Image 31

Yazoo/Kees ZCBI48181 manual REPLACING BATTERY See Fig, To Attach Jumper Cables, To Remove Cables, Reverse Order

Contents

Models ZCBI48181MANUAL NO. 109994 REV. IR 09/01/04 Operators ManualGOOD SERVICE TROUBLESHOOTING CONTENTSSYMBOLS & DECALS ASSEMBLYSYMBOLS AND DECALS Safety Instructions SAFETY INSTRUCTIONSGeneral Use Personal protective equipment SAFETY INSTRUCTIONSDo as follows Driving on SlopesSAFETY INSTRUCTIONS SAFETY INSTRUCTIONS ChildrenSAFETY INSTRUCTIONS Risk for burns if touchedIMPORTANT INFORMATION TransportSAFETY INSTRUCTIONS CUSTOMER RESPONSIBILITIES SPECIFICATIONSBEFORE REMOVING THE MOWER FROM THE SKID ASSEMBLYTOOLS REQUIRED FOR ASSEMBLY TO REMOVE THE MOWER FROM CRATETO DRIVE THE MOWER OFF OF THE SKID See Operation section for location and function of controls ASSEMBLYPLEASE REVIEW THE FOLLOWING CHECKLIST CHECKLISTCHECK THE TIRE PRESSURE ASSEMBLYCONTROLS OPERATIONENGINE HOW TO USE YOUR MOWERTO SET PARKING BRAKE See Fig DECK BLADESFIGURE 4A TO ADJUST THE DECK CUTTING HEIGHT See FigOPERATION OPERATION TO ADJUST ANTI-SCALP ROLLERS See FigureTO OPERATE MOWER TO OPERATE ON HILLSOPERATION TO TRANSPORT See FigFIGURE 7A FIGURE 7BADD GASOLINE BEFORE STARTING THE ENGINETO START ENGINE See Fig CHECK ENGINE OIL LEVELOPERATION MOWING TIPSBEFORE EACH USE GENERAL RECOMMENDATIONSCUSTOMER RESPONSIBILITIES TIRES LUBRICATION CHARTOPERATOR PRESENCE SYSTEM BLADE CARETO SHARPEN BLADE See Fig BATTERYCUSTOMER RESPONSIBILITIES ENGINE CLEAN AIR SCREENCLEAN AIR INTAKE/COOLING AREAS V-BELTSSPARK PLUGS CLEANINGAIR FILTER ENGINE OIL FILTERMOWER SERVICE AND ADJUSTMENTSIDE-TO-SIDEADJUSTMENT See Figs. 13 and BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTSTO REPLACE DECK BELT FRONT-TO-BACKADJUSTMENTSeeFigSERVICE AND ADJUSTMENT SERVICE AND ADJUSTMENT FIGURE 16ATO REMOVE WHEELS FOR REPAIR TO ADJUST THE SEAT See FigTO ADJUST CONTROL LEVERS See Fig TO START AN ENGINE WITH A WEAK BATTERYSERVICE AND ADJUSTMENT REPLACING BATTERY See FigTO ATTACH JUMPER CABLES TO REMOVE CABLES, REVERSE ORDERTRACKING ADJUSTMENT TO ADJUST PARK BRAKESERVICE AND ADJUSTMENT ENGINE OIL BATTERYSTORAGE FUEL SYSTEMCYLINDERS OTHERSTORAGE CORRECTION TROUBLESHOOTING POINTSPROBLEM CAUSEBattery will not charge PROBLEMCAUSECORRECTIONTROUBLESHOOTING POINTS run when operatorWIRING SCHEMATIC Page