Manuals / Yazoo/Kees / Lawn and Garden / Lawn Mower

Yazoo/Kees ZEKH52240 Blade replacement, IMPORTANT INFORMATION Special blade bolt is heat treated

Models: ZEKH42200 ZEKH52240 ZEKH48240

1 80

Download 80 pages 6.54 Kb

Page 49

Image 49

MAINTENANCE

Blade replacement:

WARNING!

Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.

•Remove blade bolt by turning counterclockwise.

IMPORTANT INFORMATION

To ensure proper assembly, center hole in blade must align with star on cutter housing.

•Install new or re-sharpened blade with stamped "GRASS SIDE" facing towards ground/grass (down) or “THIS SIDE UP” facing deck and cutter housing.

•Install and tighten blade bolt securely.

Torque blade bolt to 45-55 ft/lbs (60-75 Nm).

IMPORTANT INFORMATION Special blade bolt is heat treated.

Replace with a Yazoo/Kees bolt if required.

Do not use lower grade hardware than specified.

8011-671

1.Blade

2.Center hole

3.Star

4.Cutter housing

5.Blade bolt (special) Blade attachment, principal

English-47

Page 49

Image 49

Yazoo/Kees ZEKH52240, ZEKH48240 Blade replacement, IMPORTANT INFORMATION Special blade bolt is heat treated, Maintenance

Contents

968999694/ZEKH42200 968999698/ZEKH48240 968999701/ZEKH52240 Operator’s manualPage OPERATOR’S MANUAL ContentsZE RIDER English-2 Introduction INTRODUCTIONCongratulations GeneralManufacturing Number Good ServiceINTRODUCTION Symbols and Decals SYMBOLS AND DECALSXxxxxxx xxxx xxxxxxxx xxx Xxxxx xxxxxx xx xxxxxxxx xxxxx xxx xxxx xxxxxxmaintenance or SYMBOLS AND DECALSof fingers passengersSafety Instructions SAFETY INSTRUCTIONSGeneral Operation Operate machine only in daylight or good artificial light SAFETY INSTRUCTIONSSlope Operation Personal Safety EquipmentSAFETY INSTRUCTIONS SAFETY INSTRUCTIONS ChildrenSafe Handling of Gasoline MaintenanceThe engine and the exhaust system, become very hot during operation Risk for burns if touchedAlways use protective glasses when handling the battery General MaintenanceSAFETY INSTRUCTIONS Risk of sparking SAFETY INSTRUCTIONSEnglish-13 IMPORTANT INFORMATION TransportSAFETY INSTRUCTIONS SAFETY INSTRUCTIONS Customer responsibilitiesControls CONTROLSCONTROLS 1. Motion Control Levers1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse2. Parking Brake 4. Seat adjustment boltsTracking 3. Fuel Shut Off Valve5. Refueling see the safety instructionsAllow engine and exhaust system to cool at least two 2 minutes CONTROLS7. Fuses 6. By pass linkageCONTROLS 8. Hour Meter 10. Ignition Switch9. Choke Control CONTROLSUSE FULL THROTTLE WHEN MOWING , for 12. Blade switch11. Throttle Control CONTROLS13. Cutting height pedal AccessoriesCONTROLS IMPORTANT INFORMATIONOperation OPERATIONTraining To move forward and backwardStarting the Engine Before StartingOPERATION Depress the control for disengaging the mower deck OPERATIONSteering controls in the outward, locked neutral position Set the throttleSet the choke control OPERATIONOpen the fuel shut off valve Turn to the start positionIMPORTANT INFORMATION Do not run the starter for more than USE FULL THROTTLE WHEN MOWING11. Press the choke control in gradually when the engine has started OPERATIONTo attach jumper cables To start an engine with a weak batteryTo remove cables, reverse order OPERATIONEnsure that no one is near the machine when engaging the Blade switch The mower deck’s anti-scalp rollers should be evenly adjustedRunning OPERATIONOPERATION Operating on hillsIMPORTANT INFORMATION Stopping conditionsOPERATION Mowing TipsOPERATION Stopping the EngineIMPORTANT INFORMATION OPERATION Moving by HandEnglish-34 Maintenance MAINTENANCEMaintenance Schedule 3. Turn ignition switch to “OFF” position and remove the key 2. Place the Blade-switch in the disengaged positionUse protective glasses when doing maintenance work 4. Make sure the blades and all moving parts have completely stoppedTo clean battery and terminals BatteryReplacing battery Procedures on contact with acid External Rinse with plenty of waterFitting the wrong spark plug type can damage the engine Ignition SystemMAINTENANCE IMPORTANT INFORMATIONMAINTENANCE Checking the Safety SystemIMPORTANT INFORMATION Checking and Adjusting the Choke Cable Checking and Adjusting the Throttle CableChecking the Engines Cooling Air Intake MAINTENANCEDo not used compressed air to clean the paper filter ServiceReplacing the Air Filter Standard air filterChecking the Fuel Pump’s Air Filter Replacing the Fuel FilterChecking Tire Pressures MAINTENANCEChecking the V-belts Checking the Parking BrakeDeck belt To replace deck beltMAINTENANCE Deck belt installation2. Place the Blade switch in the disengaged position Before performing any service or adjustment checklistIZT belt 1. Engage the parking brakeChecking the Blades Belt installationMAINTENANCE Wrap the IZT belt around the IZT pulleysIMPORTANT INFORMATION Special blade bolt is heat treated Blade replacementReplace with a Yazoo/Kees bolt if required Do not use lower grade hardware than specifiedAdjusting Cutting Height Adjusting the Mower DeckLeveling MAINTENANCETo adjust anti-scalp rollers Adjust Anti-scalp rollers with the mower on a flat level surfaceMAINTENANCE IMPORTANT INFORMATIONUse protective glasses when cleaning and washing Cleaning and WashingRemoval and installation of caster wheel Caster WheelsTo adjust parking brake Tracking adjustmentParking brake Mower is tracking to the rightLubrication LUBRICATIONLubrication Schedule Change transaxles transmission filtersLubricating in Accordance with the Lubrication Schedule Lubricating the Cables1. Front Wheel Mount 2. Front Wheel Bearings5. Engine Oil Changing the Engine Oil 4. Deck outer spindleAvoid skin contact wash with soap and water in case of spills LUBRICATIONLUBRICATION Checking the Oil LevelTransaxle Transmission Fluid Change 6. Changing the Engine Oil FilterLUBRICATION LUBRICATION 11. Install and torque the top port plugs to 180 in./lbsLUBRICATION Purging ProceduresTrouble Shooting Guide TROUBLE SHOOTING GUIDEProblem CauseEnglish-60 TROUBLE SHOOTING GUIDEUneven mowing results TROUBLE SHOOTING GUIDESTORAGE ServiceStorage Winter StorageWiring diagram WIRING DIAGRAMSTechnical Data TECHNICAL DATAZEKH42200/968999694 ZEKH48240/968999698Overall dimensions TECHNICAL DATAZEKH42200/968999694 ZEKH48240/968999698TECHNICAL DATA ZEKH52240/968999701English-66 ZEKH52240/968999701 TECHNICAL DATAEnglish-67 TECHNICAL DATA Torque SpecificationsAccessories BioClip attachment Mulch kit Collection systemConformity Certificates CONFORMITY CERTIFICATESUSA requirements Service Journal SERVICE JOURNALDelivery Service ActionSERVICE JOURNAL After the First 5-8 Hours1. Change engine oil SERVICE JOURNAL 25-Hour Service3. Check the tire pressures 4. Check battery with cables 5. Lubricate according to lubrication chartSERVICE JOURNAL 50-Hour Service1. Perform the 25-hour service 3. Change engine oil 4. Lubricate according to lubrication chartSERVICE JOURNAL 100-Hour Service1. Perform the 25-hour service 2. Perform the 50-hour service 3. Change the engine oil filter 4. Clean/replace the spark plugsSERVICE JOURNAL 300-Hour ServiceAction Action SERVICE JOURNALDate, mtr reading, stamp, sign English-76Page 07/31/07 530 131340IR