Something not working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an enginee | r. |
The dishwasher is fitted with an alarm system which can help you to quickly determine the cause of any problems. |
|
The dishwasher will not start or stops during operation, all push buttons are inoperative except for the On/Off push button and | the |
indicator light of the running programme is flashing. |
|
Press the On/Off push button to switch off the dishwasher and carry out the following suggested corrective actions listed below | . |
Once the checks have been carried out switch on the dishwasher and start a washing programme, if the fault code reappears in |
|
the digital display, contact your local Service Force Centre. |
|
Important: If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a ch | arge will |
be made, even if the appliance is in guarantee. |
|
Symptom | Fault code | Solution |
|
|
|
|
|
The machine will not start |
|
| ● The door has not been properly closed. |
|
|
| ● The plug is not properly inserted in the power socket. |
|
|
| ● There is a power failure. |
|
|
|
|
The machine does not fill | Running programme |
| ● Ensure the water tap is open. |
with water | indicator light flashes |
| ● Ensure the mains water supply has not been cut off. |
|
|
| ● The inlet hose may be squashed or bent. Reposition the hose. |
|
|
| ● The inlet hose may be blocked. Switch off the water supply and |
|
|
| clean the filter. |
|
|
|
|
The dishwasher will not drain | Running programme |
| ● The drain hose may be squashed or bent. Reposition the hose. |
| indicator light flashes |
| ● The sink may be blocked. Clear any blockages. |
|
|
| ● The drain hose extension is not correct. Follow the instructions for |
|
|
| connecting to the waste. |
|
|
| ● There is no vent in the end of the drain hose. |
|
|
|
|
General | Running programme |
| ● Switch off the dishwasher. Switch it back on and start the |
| indicator light flashes |
| programme. |
|
|
| If the alarm reappears, call the local Service Force Centre. |
|
|
|
|
The machine is noisy |
|
| ● Dishes are rattling against each other, refer to “Loading your |
|
|
| machine”. |
|
|
| ● The spray arms are knocking against the dishes. Refer to "Loading |
|
|
| your machine". |
|
|
|
|
The door is difficult to close |
|
| ● The dishwasher is not level, or not properly |
|
|
|
|
Visible lime deposits or |
|
| ● Check that there is salt and that the salt cap is tight. |
white film on the dishes |
|
| ● Check that the right level of the water softener is set. |
|
|
|
|
The dishes are not quite dry |
|
| ● The rinse aid has run out or too little is being used. |
|
|
|
|
The dishes are not clean |
|
| ● The baskets are too full. |
(poor wash) |
|
| ● The dishes have not been arranged properly. |
|
|
| ● The spray arms do not rotate |
|
|
| ● The spray arms are clogged. |
|
|
| ● The filters are clogged. |
|
|
| ● The filters are not in the correct position. |
|
|
| ● Not enough detergent has been used or it is unsuitable. |
|
|
| ● The detergent is old or has gone hard. |
|
|
| ● The salt container cap is not properly closed. |
|
|
| ● The washing programme selected is too gentle. |
|
|
|
|
If after all these checks, the problem persists, contact your local Service Force Centre, quoting the model and serial number. This information can be found on the rating plate located on the right hand side of the dishwasher door (see picture).
Prod.No. | ........ | Ser. No |
Mod |
|
|
RA01 |
|
|
12