Before use
Before using your dishwasher for the first time:
1.Ensure that the electrical and water connections comply with the installation instructions
2.Remove all packaging from inside the appliance
3.Set the water softener
4.Pour 1 litre of water inside the salt container and then fill with salt
5.Fill the rinse aid dispenser.
Setting the water softener
T he dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance.
The higher the content of these salts, the harder your water is. Water hardness is measured in equivalent scales, Clarke degrees, French degrees and PPM (parts per Million).
The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area.
|
|
|
|
|
|
|
|
|
|
|
|
| Water hardness |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
Level |
| Clarke |
| French | PPM | Use of | |||
|
| degrees |
| degrees | (Parts per | salt | |||
|
|
|
| (°TH) | Million) |
| |||
|
|
|
|
|
|
|
| ||
1 | < 6 |
|
| < 8 | < 80 |
| NO | ||
2 | 6 - 21 |
| 8 - 30 | 81 - 300 |
| YES | |||
3 | 22 - 35 |
| 31 | - 50 | 301 | - 500 | YES | ||
4 | 36 - 49 |
| 51 | - 70 | 501 | - 700 | YES | ||
5 | 50 - 63 |
| 71 | - 90 | 701 | - 900 | YES | ||
|
|
|
|
|
|
|
|
|
|
The dishwasher is factory set at level 3.
The current level is indicated by the number of flashes |
| ||||
made by the push button | 1 indicator light, that alternates 5 |
| |||
seconds off with a number of flashes, this for about 60 |
| ||||
seconds. |
|
|
|
| |
Example: |
|
|
|
| |
1 flash | = | level 1 |
|
| |
2 flashes | = | level 2 |
|
| |
3 | flashes | = | level 3 |
|
|
4 | flashes | = | level 4 |
|
|
5 | flashes | = | level 5 |
|
|
4. To change the level, press the programme push button | 1 . | ||||
Each time the push button is pressed the level changes. |
|
Example:
If the current level is 3, by pressing the programme push button 1 once, level 4 is selected.
If the current level is 5, by pressing the programme push button 1 once, level 1 is selected.
The | push button | 1 indicator light remains off for about |
5 seconds after | which it starts flashing indicating the | |
new | level selected. |
5.To memorise the new level, switch off the dishwasher by
pressing the | On/Off | push button. |
Filling with salt
Only use salt specifically designed for use in dishwashers.
All other types of salt not specifically designed for use in a dishwasher, especially table salt, will damage the water softener.
Only fill with salt just before starting one of the complete washing programmes. This will prevent any grains of salt
or salty water, which may have been spilled, remaining on the bottom of the machine for any period of time, which may cause corrosion.
If this level is not suitable for your area the softener should be adjusted.
To select a different level be sure that the dishwasher is off and then proceed as follows:
1. | Press | 1 | and | 3 | programme push buttons simultaneously. |
|
| ||
2. | While keeping the programme push buttons | 1 and | 3 |
| |||||
| pressed switch on the dishwasher by pressing the |
| On/Off | ||||||
| push button .The |
| On/Off | indicator light comes on. |
|
| |||
| At the same time the programme push buttons | 1 | and | 3 | |||||
| start flashing. |
|
|
|
|
|
| ||
3. | Press the push button |
| 1 , the indicator light of the push |
|
| ||||
| button | 3 | turns off, while the indicator light of the push |
|
| ||||
| button | 1 | remains | fixed for about 5 seconds and then | starts |
|
|
To fill:
1.To fill with salt, unscrew the cap of the salt container.
2.Pour 1 litre of water inside the container ( only before filling with salt for the first time
3.Using the funnel provided, pour in the salt until the container is full.
Do not worry if water over flows from the unit when filling with salt, this is quite normal.
4.Replace the cap making sure that there is no trace of salt on the screw thread
or on the gasket. | SR14 |
|
5. Screw on the cap tightly.
this is necessary
).
SALET
SAL
SALZ
SEL
flashing indicating the current level of the water softener.
SO462
The salt container will require topping up periodically.
The salt cap has a refill indicator window in the centre.
A green float is clearly visible when there is salt inside the container, and almost disappears when the salt has finished reminding you to add salt.
S R11 |
5