Important safety requirements, Location

Important safety requirements

This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition).

Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Editions. The hob should not be installed in a bed sitting room with a volume of less than 20 m3. If it is installed in a room of volume less than 5 m3 an air vent of effective area of 110 cm2 is required. If it is installed in a room of volume between 5 m3 and 10 m3 an air vent of effective area of 50 cm2 is required, while if the volume exceeds 11 m3 no air vent is required.

However, if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 m3 and 11 m3.

If there are other fuel burning appliances in the same room, B.S. 5440 Part 2 Current Edition, should be consulted to determine the requisite air vent requirements.

Location

The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not in a bathroom, shower room or garage.

Before making the cut out in the worktop ensure that the edges of the hob that are to be near either a side or rear wall have a minimum distance of 55 mm. between the edge of the hob and the wall.

The minimum distance combustible material can be fitted above the hob is 400

mm.If it is fitted below 400 mm. a space of 50 mm. must be allowed from the edges of the hob.

The minimum distance combustible material can be fitted directly above the hob is 700 mm. A minimum distance of 100 mm. must be left between the side edges of the hob and any adjacent cabinets or walls.

Installation

		FITTING THE GAS HOB
WITHOUT A COOKER HOOD ABOVE
			600 mm
700 mm
		400 mm
			mm
			55	400 mm
				400 mm
100	mm	50	mm
100			mm

				50	mm
					mm
				FO 2369*

			FITTING THE GAS HOB
		WITH A COOKER HOOD ABOVE
				600 mm
700 mm
			400 mm
				mm
				55
				400 mm
100	mm		50	mm
100				mm

				50	mm
					mm
				FO 2231*

IMPORTANT

WHEN THE HOB IS FIRST INSTALLED

This hob must be installed by qualified personnel to the relevant British Standards.

Any gas installation must be carried out by a registered CORGI installer.

The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored.

Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory.

On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force.

Gas Connection

Connection to the gas supply should be with either rigid
or semi-rigid pipe, i.e. steel or copper.
The connection should be suitable for connecting to RC
1/2 (1/2 BSP male thread).
When the final connection has been made, it is essential
that a thorough leak test is carried out on the hob and
installation. Ensure that the main connection pipe does
not exert any strain on the hob.
It is important to install the elbow correctly, with
the shoulder on the end of the thread, fitted to the
hob connecting pipe.
Failure to ensure the correct assembly will cause
leakage of gas.	FO 0264

FO 0814

A)End of shaft with nut

B)Washer

C)Elbow

ZGG 642 ZGG 752 specifications

The Zanussi ZGG 642 and ZGG 752 are both impressive gas cooktops designed to elevate your cooking experience. These models highlight a range of features, technologies, and characteristics that cater to the needs of modern home chefs.

The Zanussi ZGG 642 is a stylish and functional 60 cm gas hob that provides four burners, allowing you to prepare multiple dishes simultaneously. This model includes a high-efficiency burner, ensuring that cooking is quicker and more energy-efficient. Each burner is designed with user convenience in mind, featuring a robust cast iron grille that offers durability and stability for your pots and pans. Further enhancing the cooking experience, the automatic electronic ignition system enables swift lighting of the burners with just a simple turn of the control knobs, eliminating the need for matches or lighters.

Moreover, the ZGG 642 boasts an elegant and intuitive design, available in stainless steel finish, which not only adds a modern touch to your kitchen but also ensures easy clean-up. The surface is resistant to stains and spills, making maintenance hassle-free. The control knobs are positioned at the front, providing easy access and safety, particularly for families with children.

On the other hand, the Zanussi ZGG 752 offers a larger 75 cm width, featuring five burners for those who require additional cooking space. This model is designed for versatility, with one of the burners specifically engineered to accommodate the largest pots or woks, making it perfect for stir-frying or preparing larger meals. Like the ZGG 642, the ZGG 752 also includes the robust cast iron grilles, ensuring pot stability during cooking.

Both models feature flame failure device technology, which automatically cuts off the gas supply if the flame is accidentally extinguished, enhancing safety during use. The hob features smooth, easy-to-use controls that give a precise response for simmering, boiling, or frying.

Overall, the Zanussi ZGG 642 and ZGG 752 cooktops combine efficiency, safety, and sophisticated design, making them excellent additions to any contemporary kitchen. Whether you are cooking a simple family dinner or preparing a feast for guests, these gas hobs cater to all cooking needs with style and reliability.

Zanussi ZGG 642 ZGG 752 Important safety requirements, Installation, Location, Gas Connection

Models: ZGG 642 ZGG 752