OPT12, How you can maintain the best control | Zenoah TR2300

OPT12

English

11. Optional blade usage

3.How you can maintain the best control:

a.Keep a good, firm grip on the unit with both hands. A firm grip can help neutralize bounce. Keep your right and left hands completely around the respective handles.

b.Keep both feet spread apart in a comfortable stance and yet braced for the possibility that the unit could bounce. Do not overreach. Keep firm footing and balance.

■MAINTENANCE BLADE

• Check the blade and the fasteners for looseness, cracking, or bending.

• Check the cutting edges and reform with a flat file.

(A)22, 24-tooth blade

(B)8-tooth blade

(C)4-tooth blade

Point (OPT12) :

1.Keep the end corner sharp.

2.Round the root of the edge, using round file.

3.Do not use water when using a grinder.

IMPORTANT

•It is recommended that filing should be done by professionals.

•Especially regarding filing the 22,24-tooth blade, Leave it to the professionals.

■TRANSPORTING THE UNIT

•When you finish cutting in one location and wish to continue work in another spot, turn off the engine, and lift up the unit and carry it paying attention for the blade.

•Never forget to place the protective cover over the blades.

•When transporting the unit over long distances, detach the blade fix the unit by ropes.

50

Image 50

Zenoah TR2300 How you can maintain the best control, Maintenance Blade, 22, 24-tooth blade Tooth blade Point OPT12

Contents

TR2300S Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido TR2300S SpecificationsParts location Especificaciohes Emplacement des pieces Situación de las piezasFiche technique Emission Control Symbols on the machinePosition Control DE Emisiones EmplacementPosición Working Circumstance For safe operationWorking Condition Condiciones DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail Precauciones Working Plan Before Starting the Engine DE LA Machine Plan DE TravailPlan DE Trabajo Avant DE Mettre LE Moteur EN Marche Using the Product Starting the Engine Utilisation DE LA Machine USO DEL Producto Demarrage DU MoteurArranque DEL Motor Maintenance If Someone Comes SI Alguien SE Aproxima SI QUELQU’UN S’APPROCHEEntretien Mantenimiento Transportation Handling FuelRefill after cooling the engine Manipulación DEL Combustible Manipulation DU CarburantTransport Llenar una vez que el motor se haya enfriado Installing Handle Set upSE1 SE2 SE3 Connecting Switch Wires Installing Debris Guard Assemblage Montaje Recommended Mixing Ratio Gasoline 50OIL When using Zenoah genuine oilFuel Lors de l’utilisation de la véritable huile Zenoah Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 Aceite For Your Engine LIFE, Avoid HOW to MIX FuelFueling the Unit Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA Unidad Fuel Aceite Para USO EN Motores DE 4-TIEMPOS Cutting head will start rotating upon the engine starts OperationOP1 OP2 OP3 Starting Engine Stopping Engine OP2 Cómo Parar EL Motor OP2 Fonctionnement UsoArret DU Moteur OP2 OP4 Adjusting Throttle CableAdjusting Idling Speed OP5 OP5 Travail DE Coupe Utilisation DE LA Tete a FIL Reglage Câble D’ACCÉLÉRATEUR Ajuste Cable DEL AceleradorReglage DU Ralenti OP5 Coupe DE Gazon OU D’HERBES Adjusting the Line Length Reglage DE LA Longeur DU FIL DE Coupe Ajuste DE LA Longitud DE LA Línea Maintenance Maintenance Chart Tableau D’ENTRETIEN EntretienMantenimiento Tabla DE Mantenimiento AIR Filter MA1 MA2 MA3Refilling Trimming Line MA1 Fuel Filter Filtre a Carburant Entretien MantenimientoFiltre a AIR Filtro DE Aire MA5 Replacement Plug is a NGK BPMR7AMA4 Spark Plug PARE-ETINCELLES Couple DE SerrageSilencieux LA Bujía DE Recambio Debe SER UNA Bujía NGK BPMR7A Intake AIR Cooling Vent MA6 MA7Gear Case MA6 Cylinder Intake air cooling vent back Boitier DE Renvoi D’ANGLE MA6 Caja DE Engranajes MA6 Cilindro Toma de aire de refrigeración posterior MA8 Procedures to be Performed After Every 100 Hours of USEStorage Entretien Mantenimiento Rangement Almacenamiento OPT1 OPT2 OPT3 OPT4 SET UP the Hanger OPT1Optional blade usage Hanger complete Shoulder strap T3300-17100 Monte EL Colgador OPT1 Utilisation de la lame optionnelle Uso de hoja opcionalMise EN Place DE LA Fixation OPT1 PAR Torsor Choose the Blade SET UP the BladeOPT5 OPT6 OPT7 Balance Unit Mise EN Place DE LA Lame Monte LA Hoja Choisir LA LameElija LA Hoja Standard Operation OPT8 OPT9 OPT10Cutting Method Método DE Corte Methode DE CoupeFonctionnement USO What causes blade thrust OPT11Controlling Blade Thrust How you can reduce the chance of blade thrust Controle DES Coups DE Recul Control DEL Contragolpe DE LA Hoja How you can maintain the best control Maintenance BladeOPT12 22, 24-tooth blade Tooth blade Point OPT12 Cuál es la mejor forma de mantener el control Utilisation de la lame optionnelle Uso de hoja opcionalComment conserver le meilleur contrôle de la machine Entretien Lame Guide de localisation des pannes Troubleshooting guide12. Guía de localización y solución de problemas TR2300S Nota Drive Unit TR2300S S/N 51000101 and up Optional Blade & Accessories Engine Unit TR2300S S/N 51000101 and up Cylinder Carburetor Carburetor TR2300S Manufacturer’s warranty coverage Owner’s warranty responsibilities Limited Warranty RedMax Garantie limitée Garantía Limitada Komatsu Zenoah America INC