Zoom H2 Setup examples, Recording, ,

4-Channel Mode Recording

ZOOM H2

29

Setup examples

The recommended placement when using the

H2 in 4-channel mode is shown below.

■

Recording a band rehearsal

When the members of the band are facing

each other, the H2 can be placed in the middle

to record sound coming from the front and

rear.

HINT

The front/rear/left/right balance can easily be

adjusted after a recording was made in 4-

channel mode.

■

Field recording

Position the H2 upright and have the front

panel face the main sound source.

NOTE

If you hold the H2 in your hand during field

recording, scratching noises may occur which

will detract from the recording. To avoid this,

mount the H2 on the supplied mic clip adapter

and grasp the adapter using a glove.

Recording

To record in 4-channel mode, proceed as

follows.

HINT

• In the initial condition, the H2 in 4-channel

mode is set up to record two stereo WAV

ﬁles (16 bit quantization, sampling frequency

44.1 kHz). The settings for quantization and

sampling frequency can be changed (

→

p.

35).

• After recording in 4-channel mode, you can

adjust the front/back/left/right balance and

convert the result into a single WAV ﬁle (

→

p.

57).

1.

Bring up the 4-channel mode top

screen.

2.

Adjust the input sensitivity.

In 4-channel mode, only the built-in mics can

be used. Set the input sensitivity to a suitable

value using the [MIC GAIN] switch.

Select the position of the [MIC GAIN] switch

so that the [MIC ACTIVE] indicator on the

front panel or rear panel does not flash when

the volume of the sound source is at

maximum. For information on recommended

[MIC GAIN] switch settings, see page 15.

3.

Set the H2 to the recording

standby condition.

Contents

Main H2-E.fm 2 SAFETY PRECAUTIONS / Usage Precautions ZOOM H2 W SAFETY PRECAUTIONS Cleaning Contents Convenient Recording Functions ........ 35 SD Card Operations .............................. 60 File Operations ...................................... 47 Convenient Playback Functions .......... 45 Tuning an Instrument ............................ 63 Using the Metronome Function ............67 Other Functions ..................................... 78 Connecting the H2 to a Computer ....... 71 What the H2 Can Do Using an external mic Using the built-in mics p. 12, p. 18) Page Page Parts of the H2 Front panel Rear panel Left side panel Bottom panel Internal clock date/time setting Right side panel Getting Connected H2 Left side panel H2 Right side NOTE panel AC adapter Operation on Battery Power NOTE HINT Open the battery compartment cover. Page Power-on Turn power on in the order H2 Insert a SD card into the H2. H2 H2 Setting the input sensitivity and recording level Set the sensitivity of the built-in mics. Set the H2 to the recording standby condition and adjust the recording level. Cancel the recording standby condition. Recording and playback H2. Stop recording. Set the H2 to the recording Stereo Mode Recording About the stereo mode Setup example (1): Built-in mics Setup example (2): External mic Setup example (3): External component Selecting the mic pattern for the built-in mics Select the mic pattern. Verify that nothing is connected to the [EXT MIC IN] jack or [LINE IN] jack. Page Recording Adjust the input sensitivity. Activate the source to record. Bring up the stereo mode top Adjust the recording level. 8. Stop the recording. Playback Select the file to play. Bring up the stereo mode top screen on the display. Play the selected file. 4-Channel Mode Recording About the 4-channel mode 4-Channel Mode Recording Option function symbol Counter Recorder status 4-channel mode symbol File name Setup examples Recording Adjust the input sensitivity. Bring up the 4-channel mode top Adjust the recording level. Stop the recording. Playback Play the selected file pair. Select the file pair to play. Bring up the 4-channel mode top screen on the display. Adjusting the front/rear/ left/right balance Bring up the 3D PAN menu. (3D panning) Page Adjust the 3D panning setting. Convenient Recording Functions Bring up the REC MODE screen. mode Selecting the recording Select the recording mode. Using the AGC/compressor/ limiter function Bring up the AGC/COMP screen. Select the function from the AGC/compressor/limiter options. Attenuating the low Activate the low-cut filter. Bring up the LO CUT screen. frequencies Using the auto record Bring up the AUTO REC screen. Set the various parameters for the auto record function. Set the auto record function to ON and set the start level. Use the auto record function. Using the pre-record Activate pre-recording. Bring up the PRE REC screen. Carry out recording. Bring up the MONO MIX screen. 4-channel mode Stereo mode Set the MONO MIX function to ON. Perform the steps for recording. Convenient Playback Functions Select the play mode. Bring up the PLAY MODE screen. Selecting the play mode Using the A-B repeat Cancel repeat playback. Perform repeat playback. Specify point B. File Operations Files and folders Selecting a folder (stereo mode only) Select the folder. Bring up the stereo mode main Select the file. Choose "SELECT". Viewing file information Select the file whose information you want to check. Bring up the FILE INFORMATION Assigning a name to a file Bring up the stereo mode main Select the file whose name you want to change. Edit the file name. When the file name is as you want it, confirm the change. Deleting a file Perform the file delete process. Select the file to delete. Dividing a file (stereo mode only) Perform the file division process. Bring up the FILE DIVIDE screen. Select the file to divide. Raising the overall file level (normalize function) Select the file whose level you want to normalize. (stereo mode only) Bring up the FILE NORMALIZE Converting a WAV file into an MP3 file Bring up the stereo mode main Select the WAV file for conversion to MP3 format. 4. Select the bit rate for the MP3 file. Perform the MP3 conversion. Converting a 4-channel file pair to a stereo file (4-channel mode only) Bring up the 4-channel mode main menu screen. Select the store target folder. Perform the stereo file conversion. Checking the mark list Bring up the MARK LIST screen. Select the file whose mark list you want to check. SD Card Operations Bring up the SD CARD screen. time on the card Checking the remaining Formatting a card Bring up the SD CARD screen. Bring up the CARD FORMAT SD card dropout errors Tuning an Instrument Perform tuning. Using the chromatic tuner Using the dedicated guitar/ Select the desired tuner mode. bass tuner Perform tuning. Adjusting the reference pitch of the tuner Select the reference pitch. Bring up the TUNER CALIB Using the Metronome Function Switch the pre-count on or off. pre-count on and off Switching the metronome/ Specify the metronome tempo. Making metronome/ pre-count optional settings Bring up the METRONOME Set the volume level for the metronome/pre-count. Connecting the H2 to a Computer reader Using the H2 as a card Page About the audio interface functions Using the H2 as an audio interface Select the sampling frequency. Preparations for connection Connect the [USB] port of the H2 to a USB port on the computer, using a USB cable. Bring up the USB AUDIO I/F Enabling audio interface functions Connect the [USB] port of the H2 to a USB port on the computer, using a USB cable. Bring up the USB AUDIO I/F Have the H2 recognized by the Select the input source and make settings for input sensitivity and recording level. Bring up the USB AUDIO I/F 8. Cancel the connection to the 9. Other Functions Set the date and time. Bring up the DATE/TIME screen. Setting the date and time Using the monitor function Select the desired setting. Bring up the MONITOR screen. Supplying power to an external mic Switch plug-in power on or off. (stereo mode only) Bring up the PLUG-IN POWER Adjusting the display Adjust the contrast. Bring up the CONTRAST screen. contrast Controlling the backlight on/off setting Select the backlight setting. Bring up the LIGHT screen. Specifying the battery type Select the battery type setting. Bring up the BATTERY TYPE Making settings for the key hold function Disable the key hold function. Enable the key hold function. Page Specifications Page Troubleshooting Other problems playback Problems during recording/ Error Messages Please pull out external input Index