Husqvarna CTH180 XP 02764 To Assemble and Install Mulcher Plug See Fig, Bagger Adjustment See Fig

Page 9

ASSEMBLY

DUMP HANDLE TUBE

RETAINER
SPRING
1/4 X 2"
CARRIAGE	CLEVIS
BOLTS	PIN
	CAP
1/4 LOCK NUT
FRONT BAGGER TUBE

02593

VINYL BINDING

TO ASSEMBLE AND INSTALL MULCHER PLUG (See Fig. 8)

•Remove spring retainer and pin from handle.

•Insert plug into handle. Make sure that the letter "A" on both the plug and handle are on the same side and that they can both be seen from the top when laying on the ground.

•Secure with pin and retainer spring provided. For in- stallation see "To Convert Mower" in Section 5 of this manual.

HANDLE

RETAINER

SPRING

FIG. 6

BAGGER ADJUSTMENT (See Fig. 7)

For proper bag function and appearance, it may be nec- essary to adjust the bagger assembly.There should be 6mm (1/4")-9mm (3/8") gap between the bagger top and fender and the bagger top surface should be even with the top surface of the fender. To adjust bagger position:

HORIZONTAL ADJUSTMENT

•Slightly loosen the nuts securing the bagger RH and LH horizontal adjustment brackets.Loosen only enough so the brackets keep their position, but allow them to be moved.

•Move the brackets the amount forward or backward you wish the bag assembly to move. Retighten the nuts securely.

VERTICAL ADJUSTMENT

•Slightly loosen the nuts securing the vertical adjust- ment brackets. Loosen only enough so the brackets keep their position, but allow them to be moved.

•Move the brackets the amount up or down you wish the bag assembly to move. Retighten the nuts securely.

•Reinstall the bagger assembly and check the bagger to fender ﬁ t. If necessary, repeat the procedure until proper ﬁt is attained.

6MM (1/4") - 9MM (3/8")

TOP SURFACES

EVEN

HORIZONTAL

ADJUSTMENT

BRACKET

VERTICAL

ADJUSTMENT

BRACKET

02329

FIG. 7

PIN	A

A

PLUG

0221 4

FIG. 8

9

Image 9

Contents CTH180 XP Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Steering Wheel Seat Unassembled PartsTools Required for Assembly AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidControls Install Seat See FigTo Assemble Bagger See Figs To Install Bagger Components to Tractor See Figs A-4DBagger Adjustment See Fig To Assemble and Install Mulcher Plug See FigHorizontal Adjustment Vertical AdjustmentCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMulching Mowing Tips Mowing TipsTo Dump Bagger See Bagging SeeTo Convert Mower See Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Care TractorEngine Cleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Replace Headlight Bulb Interlocks and RelaysOther StorageFuel System Engine OILTroubleshooting Points With attachment clutch Service Notes TRACTOR- -MODEL NO. CTH180 XP HAUCT18H42G, Product no 17 SchematicElectrical KEY Part Description 213 817 00 Chassis and EnclosuresDrive Repair Parts Steering Assembly 532 19 Steering Wheel KEY Part Description KEY Part NO. no Seat AssemblyWheels & Tires DecalsOptional Equipment EngineMower Lift Mower Repair Parts Bagger Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation