Husqvarna CTH180 XP 02764 To Adjust Steering Wheel Alignment, Front Wheel TOE-IN/CAMBER

Page 25

SERVICE AND ADJUSTMENTS

BELT INSTALLATION -

Carefully work new belt down around transmission cooling fan and onto the input pulley.

Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley.

Install belt through all stationary idlers and clutching idler.

Reinstall clutch locator and tighten nut securely.

Reconnect clutch harness.

Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

CLUTCH LOCATOR

ELECTRIC

CLUTCH

 

CLUTCHING

IDLER

STATIONARY

IDLERS

CLUTCH

WIRE HARNESS

TRANSMISSION

INPUT PULLEY

Loosen the adjustment bolt.

Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

ADJUSTMENT

BOLT

02239

FIG. 32

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

02201

FIG. 31

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT(See Fig. 32)

The motion control lever has been preset at the factory and adjustment should not be necessary.

Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

Start engine and move motion control lever until tractor does not move forward or backward.

Hold motion control lever in that position and turn engine off.

While holding motion control lever in place, loosen the adjustment bolt.

Move motion control lever to the neutral (N) (lock gate) position.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

TO REMOVE WHEEL FOR REPAIRS (See Fig. 33)

Block up axle securely.

Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

NOTE: To seal tire punctures and prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

 

663

 

00

 

SQUARE KEY

 

(REAR WHEEL ONLY)

25

FIG. 33

Image 25
Contents CTH180 XP Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Steering Wheel Seat Unassembled PartsTools Required for Assembly AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidControls Install Seat See FigTo Assemble Bagger See Figs To Install Bagger Components to Tractor See Figs A-4DBagger Adjustment See Fig To Assemble and Install Mulcher Plug See FigHorizontal Adjustment Vertical AdjustmentCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMulching Mowing Tips Mowing TipsBagging See To Dump Bagger SeeTo Convert Mower See Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Care TractorEngine Cleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Replace Headlight Bulb Interlocks and RelaysOther StorageFuel System Engine OILTroubleshooting Points With attachment clutch Service Notes TRACTOR- -MODEL NO. CTH180 XP HAUCT18H42G, Product no 17 SchematicElectrical KEY Part Description 213 817 00 Chassis and EnclosuresDrive Repair Parts Steering Assembly 532 19 Steering Wheel KEY Part Description KEY Part NO. no Seat AssemblyWheels & Tires DecalsOptional Equipment EngineMower Lift Mower Repair Parts Bagger Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation