Husqvarna CTH180 XP 02764 owner manual To Install Bagger Components to Tractor See Figs A-4D

Page 8

ASSEMBLY

TO INSTALL BAGGER COMPONENTS TO TRACTOR (See Figs. 4A-4D)

•Remove discharge chute from rear of tractor. Unhook the two (2) straps and pull chute out and away from tractor.

•Remove the two (2) 3/8 nuts and fl at washers from the bolts at the tractor back plate.

DISCHARGE

CHUTE

3/8 NUT

FLATWASHER

0 2277

FIG. 4A

•Using the nuts and fl at washers removed from tractor back plate, install the bagger support tube to the back plate as shown. Tighten securely.

SUPPORT

TUBE

FLAT

WASHER

3/8 NUT

BOLT

02330

 

FIG. 4B

•Install the two upper support brackets through the back plate and to the chassis, install the clevis pin 10x17mm and secure with retainer spring.

•Assemble both support brackets to the outside of the baggger support tube install the clevis pin 10x50mm and secure with retainer spring.

•Replace discharge chute into rear opening of tractor. Secure the chute with the two hook straps.

CLEVIS PIN 10 X 17MM

CLEVIS PIN 10 X 50MM

SUPPORT BRACKET 13/32 FLAT WASHER

RETAINER SPRING

SUPPORT BRACKET

0 2813

FIG. 4C

NOTE:The strap hook must go through the discharge chute only. Do not allow the hook to enter the slot in the tractor back plate.This will allow the discharge chute to float with the mower deck when moving on uneven terrain.

DISCHARGE

CHUTE

HOOK

02306

BACKPLATE

SLOT

FIG. 4D

TO ASSEMBLE BAGGER (See Figs. 5 & 6)

NOTE: For ease of assembly, you may wish to obtain the assistance of another person when putting the bagger together.

•Holes in front bagger tube are at an angle. Place front bagger tube against lower bagger tube and check for proper hole alignment before assembling bolts.

•Assemble front and lower bagger tubes using four (4) 1/4 x 50,8mm carriage bolts and lock nuts supplied. Tighten securely.

FRONT BAGGER TUBE

LOWER

BAGGER

 

 

 

 

TUBE

1/4 X 2"

 

 

CARRIAGE

1/4 LOCK

 

BOLTS

2

0259

 

NUT

 

FIG. 5

•Slide front and lower bagger tube assembly into the bagger assemby.

•Assemble front and upper bagger tubes using four (4) 1/4 x 50,8mm carraige bolts and lock nuts supplied. Tighten securely.

•Slip all the vinyl bindings over the bagger tubes

•Slide the bagger dump handle through the hole in the bagger top, install the clevis pin and secure with retainer spring.

•Push cap over end of bagger dump handle.

NOTE: For future use, the clevis pin may be removed in order to use the handle to clear the chute in the event it has become clogged.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents CTH180 XP Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Unassembled Parts Steering Wheel SeatAssembly Tools Required for AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidInstall Seat See Fig ControlsTo Install Bagger Components to Tractor See Figs A-4D To Assemble Bagger See FigsTo Assemble and Install Mulcher Plug See Fig Bagger Adjustment See FigHorizontal Adjustment Vertical AdjustmentCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsTo Convert Mower See To Dump Bagger SeeBagging See Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade CareEngine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points With attachment clutch Service Notes Schematic TRACTOR- -MODEL NO. CTH180 XP HAUCT18H42G, Product no 17Electrical KEY Part Description 213 Chassis and Enclosures 817 00Drive Repair Parts Steering Assembly 532 19 Steering Wheel Seat Assembly KEY Part Description KEY Part NO. noDecals Wheels & TiresEngine Optional EquipmentMower Lift Mower Repair Parts Bagger Warranty Statement Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX
Top Page Image Contents