Husqvarna CTH2036 XP owner manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 24

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 26 and 27)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE OF

 

BOTTOM EDGE

MOWER

00598

OF MOWER

 

 

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

FIG. 26

SUSPENSION ARM

01553

LIFT LINK ADJUSTMENT NUT

FIG. 27

FRONT-TO-BACK ADJUSTMENT (See Figs. 28 and 29)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

01268

MANDREL

"D"

"D"

FIG. 28

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

01267

NUT "E"

NUT "F"

TRUNNION

FRONT LINKS

FIG. 29

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents CTH2036 XP Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts Steering Wheel SeatKey Slope Sheet Assembly Tools Required for AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidInstall Seat See Fig To Install Bagger Components toTractor See Figs A-4D Bagger Adjustment See To Assemble Bagger See Figs A-5CHorizontal Adjustment Vertical AdjustmentTo Assemble and Install Mulcher Plug See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig Using the Reverse Operation System See FigTo Operate Mower See Fig Reverse Operation System ROSService REMINDER/HOUR Meter To Operate on HillsTo Transport See Figs Before Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsTo Dump Bagger See Bagging SeeTo Convert Mower See Maintenance Lubrication ChartTractor Blade CARESee Figs.20-22Star Pattern Blade Engine Cleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt To Check and Adjust Brake See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Adjust Throttle Control Cable To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points With attachment clutch Schematic TRACTOR- -MODEL NO. CTH2036XP 96061015800, Product no 61Electrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly 532 19 Steering Wheel Engine 532 17 Control Throttle Seat Assembly 532 18 SeatDecals Mower 532 14 67-63 Pulley Idler V-Groove Dim Mower Lift Bagger Service Notes Service Notes Warranty Statement Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 40 36-03 Rev 11.08.06 JS

CTH2036 XP specifications

The Husqvarna CTH2036 XP is a premium riding lawn mower designed for homeowners who seek an efficient and high-performance solution for maintaining their lawns. This powerful machine brings together advanced technology, robust construction, and user-friendly features to ensure an excellent mowing experience.

One of the standout features of the CTH2036 XP is its powerful 20 HP Kohler engine. This engine provides the necessary torque and reliability to handle various mowing conditions with ease. The engine is also designed for fuel efficiency, allowing users to maximize mowing time while minimizing fuel expenses.

The CTH2036 XP boasts a 36-inch cutting deck, which is perfect for maneuvering through tight spaces and achieving a clean, even cut. The deck is equipped with three high-performance blades that ensure a superior grass-cutting experience. Additionally, the cutting height can be easily adjusted, allowing users to set the desired length for their lawn seamlessly.

Another significant characteristic of the CTH2036 XP is its ergonomic design. The mower features an adjustable high-back seat that provides comfort during extended mowing sessions. The easy-to-reach controls are intuitively placed to enhance the overall user experience, making operation simple even for those new to riding lawn mowers.

Husqvarna has also integrated several innovative technologies into the CTH2036 XP. One key feature is the warranty, which offers peace of mind through its reliable performance and durability. The addition of the Easy Start system allows for effortless starting, requiring only the turn of a key to get going.

Moreover, the mower is equipped with a robust transmission system that delivers smooth acceleration and deceleration. Users can effortlessly navigate different terrains while maintaining control over the machine. An important aspect of the CTH2036 XP is its compact size, which makes it ideal for residential properties with a moderate amount of lawn space.

In conclusion, the Husqvarna CTH2036 XP is a versatile and innovative riding lawn mower that combines power, comfort, and technology to provide an exceptional mowing experience. Whether you are looking to maintain a well-manicured lawn or tackle overgrown grass, this model stands as a top choice in the realm of residential mowers. With its reliable performance and user-centric design, the CTH2036 XP is sure to impress even the most discerning homeowners.
Top Page Image Contents