Husqvarna CTH2036 XP Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel Alignment

Page 26

SERVICE AND ADJUSTMENTS

TO REPLACE MOTION DRIVE BELT (See Fig. 32)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Disconnect clutch wire harness.

•Remove clutch locator.

•Remove belt from clutching idler and all stationary idlers.

•Remove belt downward from engine pulley and around electric clutch.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

BELT INSTALLATION -

•Carefully work new belt down around transmission cooling fan and onto the input pulley.

•Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley.

•Install belt through all stationary idlers and clutching idler.

•Reinstall clutch locator and tighten nut securely.

•Reconnect clutch harness.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT(See Fig. 33)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

ELECTRIC

CLUTCH

CLUTCHING

IDLER

STATIONARY

IDLERS

CLUTCH CLUTCH

WIRE LOCATOR

HARNESS

TRANSMISSION

INPUT PULLEY

02201

FIG. 32

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and beforeoperatingthetractor. See“PURGETRANSMISSION” in the Operation section of this manual.

26

ADJUSTMENT

BOLT

FIG. 33

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 34)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

• Repair tire and reassemble.

Page 25 Page 27
Image 26
Page 25 Page 27
Contents CTH2036 XP General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Key Slope Sheet Unassembled PartsSteering Wheel Seat To Remove Tractor from CAR- TON AssemblyTools Required for Assembly Before Removing Tractor from SkidTractor See Figs A-4D Install Seat See FigTo Install Bagger Components to Bagger Adjustment See To Assemble Bagger See Figs A-5CTo Assemble and Install Mulcher Plug See Fig Horizontal AdjustmentVertical Adjustment Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigUsing the Reverse Operation System See Fig Reverse Operation System ROSTo Transport See Figs Service REMINDER/HOUR MeterTo Operate on Hills ADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsTo Convert Mower See To Dump Bagger SeeBagging See Maintenance Lubrication ChartStar Pattern Blade TractorBlade CARESee Figs.20-22 Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt To Check and Adjust Brake See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Carburetor Interlocks and RelaysFuel System StorageOther Engine OILTroubleshooting Points With attachment clutch Schematic TRACTOR- -MODEL NO. CTH2036XP 96061015800, Product no 61Electrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly 532 19 Steering Wheel Engine 532 17 Control Throttle Seat Assembly 532 18 SeatDecals Mower 532 14 67-63 Pulley Idler V-Groove Dim Mower Lift Bagger Service Notes Service Notes Warranty Statement Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 40 36-03 Rev 11.08.06 JS

CTH2036 XP specifications

The Husqvarna CTH2036 XP is a premium riding lawn mower designed for homeowners who seek an efficient and high-performance solution for maintaining their lawns. This powerful machine brings together advanced technology, robust construction, and user-friendly features to ensure an excellent mowing experience.

One of the standout features of the CTH2036 XP is its powerful 20 HP Kohler engine. This engine provides the necessary torque and reliability to handle various mowing conditions with ease. The engine is also designed for fuel efficiency, allowing users to maximize mowing time while minimizing fuel expenses.

The CTH2036 XP boasts a 36-inch cutting deck, which is perfect for maneuvering through tight spaces and achieving a clean, even cut. The deck is equipped with three high-performance blades that ensure a superior grass-cutting experience. Additionally, the cutting height can be easily adjusted, allowing users to set the desired length for their lawn seamlessly.

Another significant characteristic of the CTH2036 XP is its ergonomic design. The mower features an adjustable high-back seat that provides comfort during extended mowing sessions. The easy-to-reach controls are intuitively placed to enhance the overall user experience, making operation simple even for those new to riding lawn mowers.

Husqvarna has also integrated several innovative technologies into the CTH2036 XP. One key feature is the warranty, which offers peace of mind through its reliable performance and durability. The addition of the Easy Start system allows for effortless starting, requiring only the turn of a key to get going.

Moreover, the mower is equipped with a robust transmission system that delivers smooth acceleration and deceleration. Users can effortlessly navigate different terrains while maintaining control over the machine. An important aspect of the CTH2036 XP is its compact size, which makes it ideal for residential properties with a moderate amount of lawn space.

In conclusion, the Husqvarna CTH2036 XP is a versatile and innovative riding lawn mower that combines power, comfort, and technology to provide an exceptional mowing experience. Whether you are looking to maintain a well-manicured lawn or tackle overgrown grass, this model stands as a top choice in the realm of residential mowers. With its reliable performance and user-centric design, the CTH2036 XP is sure to impress even the most discerning homeowners.
Top Page Image Contents