|
|
|
| ASSEMBLY | ||
UNPACKING CARTON (See Fig. 2) | • | Grasp handle assembly. Hold in “up” position. Be sure | ||||
|
|
|
|
|
| handle lock remains in gearcase notch. Slide handle |
CAUTION: | Be careful of exposed |
| assembly into position. | |||
staples when handling or disposing of |
|
| ||||
cartoning material. |
|
|
|
| HANDLE ASSEMBLY | |
|
|
|
|
|
| "UP" POSITION |
IMPORTANT: WHEN UNPACKING AND ASSEMBLING TILLER, |
|
| ||||
BE CAREFUL NOT TO STRETCH OR KINK CABLES. |
| TIGHTEN HANDLE LOCK | ||||
• While holding handle assembly, cut cable ties securing |
| LEVER TO HOLD | ||||
handle assembly to top frame and depth stake. Let |
|
| ||||
handle assembly rest on tiller. |
|
|
|
|
| |
• Remove top frame of carton. |
|
|
|
|
| |
• Slowly ease handle assembly up and place on top of |
|
| ||||
carton. |
|
|
|
|
|
|
• Cut down right hand front and right hand rear corners |
| LOOSEN HANDLE | ||||
of carton, lay side carton wall down. |
|
|
|
| ||
|
|
|
| LOCK LEVER TO MOVE | ||
• Remove packing material from handle assembly. |
|
| ||||
HANDLE |
|
|
|
|
| Fig. 4 |
|
|
|
|
|
| |
ASSEMBLY |
|
|
|
| • Rotate handle assembly down. Insert rear carriage bolt | |
|
|
|
|
| ||
|
|
|
|
|
| first, with bolt head on L.H. side of tiller and loosely |
|
|
|
|
|
| assemble locknut (See Fig. 5). |
|
|
|
|
| • Insert pivot bolt in front part of plate and tighten. | |
|
|
|
|
| • Cut down remaining corners of carton and lay panels | |
|
|
|
|
|
| flat. |
| c |
|
| 3 | • Lower the handle assembly. Tighten nut on carriage | |
|
|
| _ |
|
| |
|
| n |
|
|
| |
|
| rto |
|
|
|
|
| a |
|
|
| bolt so handle moves with some resistance. This will | |
|
|
|
|
|
| |
| SHIFT ROD |
| allow for easier adjustment. | |||
| • Place flat washer on threaded end of handle lock le- | |||||
|
|
|
|
|
| ver. |
|
|
|
|
| • Insert handle lock lever through handle base and | |
| Fig. 2 |
|
|
|
| gearcase. Screw in handle lock lever just enough to |
|
|
|
|
| hold lever in place. | |
|
|
|
|
|
| |
INSTALL HANDLE (See Figs. 3, 4, and 5) | • Insert second handle lock (with teeth inward) in the | |
slot of the handle base (just inside of washer). | ||
• Insert one handle lock (with teeth facing outward) in | ||
• With handle assembly in lowest position, securely | ||
gearcase notch. (Apply grease on smooth side of | ||
tighten handle lock lever by rotating clockwise. Leaving | ||
handle lock to aid in keeping lock in place until handle | ||
handle assembly in lowest position will make it easier | ||
assembly is lowered into position.) | ||
to remove tiller from carton. | ||
|
VIEWED FROM R.H. SIDE OF TILLER
HANDLE ASSEMBLY
GEARCASE
NOTCH
HANDLE
LOCK
handles_10
Fig. 3
|
|
| HANDLE |
|
|
| LOCK |
GEARCASE | FLAT | ||
|
|
| WASHER |
SLOT |
| HANDLE LOCK | |
|
|
| |
|
|
| LEVER |
CARRIAGE |
|
|
|
BOLT |
|
|
|
|
| 4 |
|
| _3 | PIVOT BOLT | |
| dles |
| |
an |
| ||
h |
|
| |
HANDLE |
| LOCKNUT | |
BASE |
|
|
|
Fig. 5
5