Husqvarna 15V2 AWD manual Storage, Winter storage, Guard, Service

Page 33

Storage

Winter storage

At the end of the season, or if the machine is going to stand idle for more than 30 days, it should immediately be made ready for storage. Fuel which is left to stand for long periods (30 days or more) can leave tacky deposits which can block the carburettor and interfere with the engine.

Fuel stabiliser is an acceptable alternative to avoid tacky deposits during storage. If alkylate petrol (Aspen) is used stabiliser is not necessary since this fuel is stable. However, one should avoid changing from standard to alkylate petrol since sensitive rubber parts can harden. Add stabiliser to the fuel in the tank or the storage container. Always use the mixing ratios indicated by the manufacturer. Run the engine for at least 10 minutes after adding the stabiliser so that it will reach the carburettor. Do not empty the fuel tank and carburettor if stabiliser has been added.

WARNING! Never place an engine with fuel

!in the tank indoors or in poorly ventilated areas where petrol fumes can come into contact with naked flames, sparks or pilot flames in boilers, hot water heaters, drying cabinets, etc. Exercise caution when handling fuel. It is highly inflammable, and careless use can cause serious injury and damage to property. Drain off the fuel in an approved container outdoors and well clear of naked flames. Never use petrol for cleaning purposes. Use degreasing agents and hot water instead.

To prepare the machine for storage follow these instructions:

1Carefully clean the machine, especially under the cutting unit. Touch-up paint damage to avoid rust.

2Inspect the machine for worn or damaged parts and tighten loose screws and nuts.

3Change the engine oil, and take care of the waste oil.

4Empty the fuel tank. Start the engine and run it until the carburettor is emptied of fuel.

5Remove the plugs and pour about a tablespoon of engine oil into each cylinder. Pull round the engine to distribute the oil and screw the plugs back on.

6Grease all grease nipples, joints and axles.

7Remove the battery. Clean it, charge it, and store it in a cool place.

8Store the machine in a clean and dry place and cover it over for extra protection.

Guard

There is a cover to protect your machine during storage or transport. Contact your dealer for a demonstration

Service

Low season is the most suitable time to perform a service or overhaul of the machine in order to ensure high function safety during high season.

When ordering spare parts state your machine’s purchase year, model, type, and serial number.

Always use genuine parts.

Annual inspection or tuning by an authorised service workshop is a good way of getting the best out of your machine the next season.

English – 33

Image 33
Contents Rider 15V2 Rider 15V2 AWD Contents Service journal Pre-delivery serviceAfter the first 8 hours Dear Customer IntroductionDriving and transport on public roads TowingSerial Number Good serviceSymbols KEY to SymbolsKEY to Symbols Safety instructions Safety InstructionsInsure your Rider General useThis is what you do Driving on slopesChildren MaintenanceTransport Location of the controls What is WHAT?Presentation Exercise care and refuel outdoors see safety instructions Cutting height adjustment leverLifting lever for the cutting unit SeatDriving Before startingStart the engine Connecting the jump leads Starting the engine with a weak batteryDriving the Rider Remove the cables in the reverse orderCutting tips Stop the engineOther objects which can be thrown out by the blades Release lever Release lever Rider 15V2 AWDRelease lever Rider Maintenance schedule MaintenanceCleaning Checking and adjusting the steering wiresRemoving of the machine hoods Adjusting the parking brake Rider 15V2 AWD Adjusting the parking brake RiderChecking and adjusting of throttle wire Can result in reduced braking abilityReplacement of fuel filter Checking and adjusting the choke wireReplacing the air filter Cool before starting to replace the air filterChecking the fuel pump’s air filter Check the level of the battery acidIgnition system Replacing the spark plugCheck the safety system Main fuse When the engine is running. Mind your fingersChecking the tyre pressure Checking the engine’s cooling air intakeTrapping your hand Removing the cutting unitAdjusting the parallelism of the cutting unit Checking the cutting unit’s parallelismReplacing the cutting unit belts Placing in the service position Service position for the cutting unitRestoring from service position Checking the bladesRemoving the BioClip plug Checking the engine’s oil level LubricationChanging the oil filter Replacing the engine oilLubricating the belt adjuster Checking the transmission oil levelGeneral lubrication Problem Procedure Troubleshooting scheduleStorage ServiceWinter storage GuardTechnical data EC-declaration of conformity Applies to Europe only 1150312-26 ´z+R?6¶6@¨ ´z+R?6¶6@¨

15V2 AWD specifications

The Husqvarna 15V2 AWD is a remarkable addition to the world of outdoor power equipment, especially designed for homeowners seeking a reliable and efficient lawn care solution. This versatile lawn mower combines robust performance with advanced technology, making yard maintenance a breeze.

One of the standout features of the Husqvarna 15V2 AWD is its all-wheel drive (AWD) system. This technology allows the mower to maintain superior traction across various terrains, ensuring optimal performance on slopes, uneven ground, and wet grass conditions. With AWD, users can navigate their lawns with ease, providing a consistent cut without the worry of slipping or losing control.

The Husqvarna 15V2 AWD is powered by a reliable engine, inherited from the brand's legacy of quality and durability. The engine is designed for efficient fuel consumption and powerful performance, allowing users to complete their mowing tasks in less time without sacrificing cutting quality. The mower's cutting deck features a durable construction that can withstand the rigors of regular use, while also providing an adjustable cutting height to tailor the lawn appearance to the user’s preference.

Ergonomically designed, the Husqvarna 15V2 AWD features an adjustable handle, providing comfort during operation. This feature, combined with its lightweight design, reduces fatigue, allowing for extended mowing sessions without discomfort. The user-friendly controls are intuitively placed for easy access, making it suitable for both novice and experienced users alike.

Another impressive characteristic of the 15V2 AWD is its ability to assimilate innovative technology for a better mowing experience. The mower is equipped with a cutting system that ensures a clean, precise cut, while mulching capabilities allow for efficient grass recycling, promoting a healthier lawn. Additionally, Husqvarna's commitment to eco-friendliness is evident in the mower's low emissions, aligning with modern environmental standards.

In summary, the Husqvarna 15V2 AWD is more than just a lawn mower; it’s a comprehensive lawn care solution that combines advanced technology, extensive features, and user-centric design. With its powerful engine, all-wheel drive capability, and ergonomic design, it stands as a reliable choice for homeowners looking to maintain their lawns with ease and precision. Whether you’re managing a small yard or tackling more extensive landscaping tasks, the 15V2 AWD is engineered to deliver exceptional results every time.