Husqvarna 11 Bio/13 H Bio manual Storage, Winter storage, Service

Page 36

STORAGE

Winter storage

At the end of the season the machine should immediately be put in order for storage, also if it is going to stand idle for more than 30 days. Fuel which is left to stand for long periods (30 days or more) can leave tacky deposits which can block the carburettor and interfere with the engine.

Fuel stabiliser is an acceptable alternative to avoid tacky deposits during storage. If alkylate petrol (Aspen) is used stabiliser is not necessary since this fuel is stable. However, one should avoid changing from standard to alkylate petrol since sensitive rubber parts can harden. Add stabiliser to the fuel in the tank or the storage container. Always use the mixing ratios indicated by the manufacturer. Run the engine for at least 10 minutes after adding the stabiliser so that it will reach the carburettor. Do not empty the fuel tank and carburettor if stabiliser has been added.

To put the machine in order for storage follow these instructions:

1.Carefully clean the machine, especially under the cutting unit. Touch-up paint damage to avoid rust.

2.Inspect the machine for worn or damaged parts and tighten loose screws and nuts.

3.Change the oil, and take care of the waste oil.

4.Empty the fuel tank. Start the engine and run it until the carburettor is emptied of fuel.

5.Remove the spark plug and pour about a table- spoon of engine oil into the cylinder. Pull round the engine to distribute the oil and screw the plug back on.

6.Grease all grease nipples, joints and axles.

7.Remove the battery. Clean it, charge it, and store it is a cool place.

8.Store the machine is a clean and dry place and cover it over for extra protection.

!WARNING!

Never place an engine with fuel in the tank indoors or in poorly ventilated areas where petrol fumes can come into contact with naked flames, sparks or pilot flames in boilers, hot water heaters, or drying cabinets, etc. It is highly inflammable and negligent usage can cause severe person injury and material damage. Drain off the fuel in an approved container outdoors and well clear of naked flames. Never use petrol for cleaning purposes. Use degreasing agents and hot water instead.

Service

When ordering spare parts state the purchase year, model, type, and serial number.

Always use genuine parts.

Annual inspection or trimming by an authorised service workshop is a good way of getting the best out of your machine the next season.

English – 35

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Rider 11/13 H Rider 11 Bio/13 H Bio 101 91Contents Explanation of Symbols Safety Instructions General useDriving on slopes Do as followsMaintenance ChildrenBattery can explode and cause severe injuries Presentation PresentationLocation of the controls Presentation Rider 11 / 11 BIO Throttle and Choke leverClutch pedal Brake pedal / Parking brakePresentation Rider 13 H / 13 H BIO Speed limiterParking brake Cutting unit Lift lever for cutting unitRider 11 Bio and Rider 13 H Bio have a twin-blade Lever for adjustment of cutting height SeatFuelling Driving Before startingStarting the engine Cold engine Warm engineDriving the machine For Rider 13 H and Rider 13 H BioFor Rider 11 and Rider 11 Bio Cutting tips Hill start, manual gearbox Stopping the engineRelease lever Rider 13 H and Rider 13 H Bio Maintenance Maintenance scheduleDaily Maintenance interval Hours 100Dismantling of the machine hoods Engine hoodFront hood Rider 11 and Rider 13 H Front hood Rider 11 Bio and Rider 13 H BioRight-hand fender Left-hand fenderCheck the engine’s oil level Check the engine’s cooling air intakeChecking of the fuel pump’s air filter Checking and adjustment of the steering wires Adjusting the brake Rider 11 and Rider 11 Bio Poorly adjusted brakes can result in reduced braking powerChecking the brake Rider 11 and Rider 11 Bio Check the level of the battery acid Check the safety systemProcedures on contact with acid Do not use compressed air to clean the paper filter Replacing the air filterChecking the cutting unit’s parallelism Adjustment of the cutting unit’s parallelism Maintenance Rider 11/11 BIO Service position for BioClipPlacing in service position Maintenance Rider 11/11 BIO Restoring from service position Checking the blades Checking the tyre pressureChanging the oil Lubrication Rider 11 and Rider 11 BioLubrication of front wheel bearings Lubrication of belt tensioner General lubricationChecking and adjustment of the throttle wire Replacement of the fuel filterTrouble Shooting Schedule Problem ProcedureService StorageWinter storage Technical Data Dimensions Rider 11 Bio Rider 13 H Bio EU declaration of conformity Only applies to Europe Svenska ´*3,¶6X¨ Svenska 2000W37

11 Bio/13 H Bio specifications

Husqvarna 11 Bio and Husqvarna 13 H Bio represent the pinnacle of innovation in the world of robotic lawn mowers. Designed for efficiency and ease of use, these models are engineered to cater to the needs of diverse lawn sizes and terrains.

The Husqvarna 11 Bio is particularly tailored for small to medium-sized gardens, handling areas up to 600 square meters with minimal intervention. Its compact design allows for seamless navigation through narrow spaces, effortlessly maneuvering around flower beds and pathways. The mowing height can be easily adjusted, ensuring a perfectly trimmed lawn while allowing for customization based on grass types and environmental conditions.

On the other hand, the Husqvarna 13 H Bio is designed for larger areas, accommodating lawns of up to 1,000 square meters. This model incorporates advanced features that make it a standout choice for homeowners with expansive green spaces. It features a robust cutting system that ensures efficient and even grass cutting, delivering a well-manicured appearance.

One of the key technologies found in both models is the Automower® Connect, which allows users to control their mower via a smartphone app. This feature enables homeowners to start, stop, and schedule mowing sessions from anywhere, offering convenience and flexibility. In addition, the models are equipped with smart sensors that detect obstacles and navigate around them, preventing any damage to the mower or surrounding plants.

Battery life is another critical aspect of the Husqvarna 11 Bio and 13 H Bio. Both mowers are built with powerful lithium-ion batteries, providing extended operating times and quick charging capabilities. This means minimal downtime and uninterrupted mowing, even during the peak growing season.

Moreover, these robotic mowers utilize a unique GPS-assisted navigation system, allowing them to create a map of the mowing area. This ensures that every inch of the lawn is covered efficiently, eliminating the need for repetitive mowing or missed spots.

With their eco-friendly lithium-ion batteries, the Husqvarna 11 Bio and 13 H Bio are not only effective but also sustainable, producing zero direct emissions during operation. Their quiet operation allows for mowing during the day or night without disturbing the household or neighbors.

In summary, the Husqvarna 11 Bio and 13 H Bio robotic mowers embody efficiency, convenience, and sustainability, making them ideal choices for modern homeowners seeking a low-maintenance solution to lawn care. Their advanced technologies and robust features ensure a beautifully maintained lawn with minimal effort.
Top Page Image Contents