Husqvarna CS 2159WH, CS 2156CWH, CS 2159CWH manual Felling cut

Page 26

WORKING TECHNIQUES

Next make the bottom cut so that it finishes exactly at the end of the top cut.

The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45°.

The line where the two cuts meet is called the directional cut line. This line should be perfectly horizontal and at right angles (90°) to the chosen felling direction.

Felling cut

The felling cut is made from the opposite side of the tree and it must be perfectly horizontal. Stand on the left side of the tree and cut on the pull stroke.

Make the felling cut about 3-5 cm (1.5-2 inches) above the bottom directional cut.

Set the spike bumper (if one is fitted) just behind the felling hinge. Use full throttle and advance the chain/bar slowly into the tree. Make sure the tree does not start to move in the opposite direction to your intended felling direction. Drive a wedge or breaking bar into the cut as soon as it is deep enough.

Finish the felling cut parallel with the directional cut line so that the distance between them is at least 1/10 of the trunk diameter. The uncut section of the trunk is called the felling hinge.

The felling hinge controls the direction that the tree falls in.

All control over the felling direction is lost if the felling hinge is too narrow or non-existent, or if the directional cuts and felling cut are badly placed.

When the felling cut and directional cut are complete the tree should start to fall by itself or with the aid of a felling wedge or breaking bar.

We recommend that you use a bar that is longer than the diameter of the tree, so that you can make the felling cut and directional cuts with single cutting strokes. See instructions under the heading Technical data section to find out which lengths of bar are recommended for your saw.

There are methods for felling trees with a diameter larger than the bar length. However these methods involve a much greater risk that the kickback zone of the bar will come into contact with the tree.

26 – English

Page 25 Page 27
Image 26
Page 25 Page 27
Contents English Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesChain Cutting equipment designed to reduce kickbackBar Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Filling with chain oil Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Checking chain lubricationNeedle bearing lubrication Checking wear on cutting equipmentFitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFuelling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsJam. Always stop the engine before cleaning Basic cutting technique TermsLog is supported at one end. There is a high risk Tree felling techniqueLimbing Safe distanceDirectional cuts Felling directionClearing the trunk and preparing your retreat Felling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburettor adjustment Checking brake band wear Correctly adjusted carburettorHigh speed jet H Checking the front hand guardChecking the inertia brake release Muffler Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springLubricating the bar tip sprocket Air filterSpark plug Needle bearing lubricationRunning when making adjustments Adjustment of the oil pumpAir Injection centrifugal cleaning Cooling systemHeated handles Temperature 0C or colderWinter use Electrical carburettor heatingMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesEN ISO 12100-22003, Cispr 122005, EN ISO EC-declaration of conformityApplies to Europe only Page Page Page Original instructions 1153185-26

CS 2159CWH, CS 2159C, CS 2156, CS 2156CWH, CS 2159WH specifications

The Husqvarna CS 2159, CS 2156C, CS 2159W, CS 2159WH, and CS 2156CWH are a series of powerful and efficient chainsaws designed for both professionals and experienced enthusiasts. These models are known for their reliability, cutting performance, and innovative features that enhance usability and productivity.

One of the standout features across these models is the Efficient Air Cleaning System, which significantly reduces wear and tear on the engine. This system pre-filters the air entering the engine, ensuring that only clean air is used, thereby extending the lifespan of the chainsaw and improving its performance. This feature is particularly beneficial in dusty environments, where traditional systems might struggle to maintain efficiency.

The CS 2159 and CS 2156C models include an advanced fuel pump that allows for easy starting, even in cold conditions. This innovation saves time and effort, making them ideal for users who need to get to work quickly. Additionally, these chainsaws come equipped with a low-vibration design that minimizes user fatigue during extended use, allowing for greater comfort without compromising performance.

A highlight of the CS 2159W and CS 2159WH models is their weather-resistant construction. These chainsaws are built to withstand adverse weather conditions, making them suitable for year-round use. The WH variant features a comfortable heated handle, which provides added warmth and grip in cold environments, ensuring that you can operate efficiently regardless of the external temperature.

All models in this series are equipped with a quick-release air filter, facilitating easy maintenance and serviceability. Regular maintenance is crucial for optimal performance, and Husqvarna has made it simple for users to keep their equipment in top condition. The chain tensioning system is also easily accessible, allowing for quick adjustments to be made on the fly, ensuring that users can maintain an optimal cutting experience.

In terms of power, the CS 2159 series boasts robust engines that provide high cutting performance while being environmentally friendly. The engines are designed to consume less fuel and emit fewer emissions, meeting modern environmental standards without sacrificing the power output that professionals require.

In summary, the Husqvarna CS 2159, CS 2156C, CS 2159W, CS 2159WH, and CS 2156CWH chainsaws are exceptional tools that combine advanced technology with user-friendly features. With reliable performance, low maintenance needs, and comfort-driven design, they stand out as top choices for both professional users and outdoor enthusiasts alike. Whether tackling heavy-duty cutting tasks or maintaining your property, these chainsaws are built to deliver consistent results.
Top Page Image Contents