Husqvarna CS 2159C Air filter, Spark plug, Lubricating the bar tip sprocket, Fitting the starter

Page 34

MAINTENANCE

Fitting the starter

•To fit the starter, first pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

•Fit and tighten the screws that hold the starter.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions

•Starting problems

•Loss of engine power

•Unnecessary wear to engine parts.

•Excessive fuel consumption.

•Remove the air filter after taking off the air filter cover. When refitting make sure that the air filter seals tightly against the filter holder. Clean the filter by brushing or shaking it.

The filter can be cleaned more thoroughly by washing it in water and detergent.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

A JONSERED chain saw can be equipped with different types of air filter according to working conditions, weather, season, etc. Contact your dealer for advice.

Spark plug

The spark plug condition is influenced by:

•Incorrect carburettor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm. The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week). CAUTION! Use a high-quality bearing grease or engine oil. See instructions under the heading Cutting equipment.

34 – English

Page 33 Page 35
Image 34
Page 33 Page 35
Contents English Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesChain Cutting equipment designed to reduce kickbackBar Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Filling with chain oil Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Checking chain lubricationNeedle bearing lubrication Checking wear on cutting equipmentFitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFuelling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsJam. Always stop the engine before cleaning Basic cutting technique TermsLog is supported at one end. There is a high risk Tree felling techniqueLimbing Safe distanceClearing the trunk and preparing your retreat Felling directionDirectional cuts Felling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburettor adjustment MaintenanceGeneral Checking brake band wear Correctly adjusted carburettorHigh speed jet H Checking the front hand guardChecking the inertia brake release Muffler Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springLubricating the bar tip sprocket Air filterSpark plug Needle bearing lubricationRunning when making adjustments Adjustment of the oil pumpAir Injection centrifugal cleaning Cooling systemHeated handles Temperature 0C or colderWinter use Electrical carburettor heatingMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesApplies to Europe only EC-declaration of conformityEN ISO 12100-22003, Cispr 122005, EN ISO Page Page Page Original instructions 1153185-26

CS 2159CWH, CS 2159C, CS 2156, CS 2156CWH, CS 2159WH specifications

The Husqvarna CS 2159, CS 2156C, CS 2159W, CS 2159WH, and CS 2156CWH are a series of powerful and efficient chainsaws designed for both professionals and experienced enthusiasts. These models are known for their reliability, cutting performance, and innovative features that enhance usability and productivity.

One of the standout features across these models is the Efficient Air Cleaning System, which significantly reduces wear and tear on the engine. This system pre-filters the air entering the engine, ensuring that only clean air is used, thereby extending the lifespan of the chainsaw and improving its performance. This feature is particularly beneficial in dusty environments, where traditional systems might struggle to maintain efficiency.

The CS 2159 and CS 2156C models include an advanced fuel pump that allows for easy starting, even in cold conditions. This innovation saves time and effort, making them ideal for users who need to get to work quickly. Additionally, these chainsaws come equipped with a low-vibration design that minimizes user fatigue during extended use, allowing for greater comfort without compromising performance.

A highlight of the CS 2159W and CS 2159WH models is their weather-resistant construction. These chainsaws are built to withstand adverse weather conditions, making them suitable for year-round use. The WH variant features a comfortable heated handle, which provides added warmth and grip in cold environments, ensuring that you can operate efficiently regardless of the external temperature.

All models in this series are equipped with a quick-release air filter, facilitating easy maintenance and serviceability. Regular maintenance is crucial for optimal performance, and Husqvarna has made it simple for users to keep their equipment in top condition. The chain tensioning system is also easily accessible, allowing for quick adjustments to be made on the fly, ensuring that users can maintain an optimal cutting experience.

In terms of power, the CS 2159 series boasts robust engines that provide high cutting performance while being environmentally friendly. The engines are designed to consume less fuel and emit fewer emissions, meeting modern environmental standards without sacrificing the power output that professionals require.

In summary, the Husqvarna CS 2159, CS 2156C, CS 2159W, CS 2159WH, and CS 2156CWH chainsaws are exceptional tools that combine advanced technology with user-friendly features. With reliable performance, low maintenance needs, and comfort-driven design, they stand out as top choices for both professional users and outdoor enthusiasts alike. Whether tackling heavy-duty cutting tasks or maintaining your property, these chainsaws are built to deliver consistent results.
Top Page Image Contents