Husqvarna 570 EPA III, 576 XP EPA III, 1152353-95 manual Tensioning the chain

Page 13

GENERAL SAFETY PRECAUTIONS

•File all the teeth to the same length. When the length of the cutting teeth is reduced to 0.16 inch (4 mm) the chain is worn out and should be replaced.

General advice on adjusting depth gauge setting

•When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain.

 

!

WARNING! The risk of kickback is

 

increased if the depth gauge setting is

 

 

too large!

 

 

 

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel

resistance as you draw the file along the depth gauge tool.

Tensioning the chain

WARNING! A slack chain may jump off

! the bar and cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Loosen the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents EPA III 576 XP EPA Symbols on the machine KEY to SymbolsSymbols in the operator’s manual You will find the following labels on your chain sawContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Cutting equipment Stop switchVibration damping system MufflerBar Cutting equipment designed to reduce kickbackChain General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Filling with chain oil Lubricating cutting equipmentChecking chain lubrication Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueLimbing Safe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatFelling cut Directional cutsFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral When the bar hits the stump the brake should be applied Correctly adjusted carburetorChecking brake band wear Checking the front hand guardChecking the brake trigger Starter MufflerChanging a broken or worn starter cord Tensioning the recoil spring Air filterChanging a broken recoil spring Fitting the starterWhen making adjustments Adjustment of the oil pumpSpark plug Lubricating the bar tip sprocketTemperature 0C 32F or colder Air Injection centrifugal cleaningCooling system Winter useHeated handles Temperature -5C 23F or colderElectrical carburetor heating 576XPGDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataYour cutting need Saw chain filing and file gaugesYour Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautions´z+TCG¶5S¨ Page 1152353-95

1152353-95, 570 EPA III, 576 XP EPA III specifications

The Husqvarna 576 XP EPA III and 570 EPA III chainsaws exemplify innovation in outdoor power equipment, designed for the demanding user who requires high performance and reliability. These models are ideal for professional loggers and landowners alike, combining power, efficiency, and advanced technology.

One of the standout features of the Husqvarna 576 XP EPA III is its powerful 72.2cc engine, which delivers exceptional cutting performance while maintaining low fuel consumption. This model incorporates the X-Torq technology, which reduces fuel consumption by up to 20% and decreases harmful exhaust emissions by up to 75%. This makes the 576 XP EPA III not only high-performing but also environmentally friendly, meeting stringent EPA emission requirements.

The 570 EPA III, slightly smaller at 65.1cc, still boasts impressive power and torque, making it suitable for a variety of cutting tasks. This model is also equipped with the X-Torq technology, offering fuel efficiency and reduced emissions. It’s tailored for users who need a reliable chainsaw for medium to heavy-duty jobs, providing both power and ease of use.

Both models feature an Air Injection system that uses centrifugal force to remove larger dust and debris particles before they reach the air filter. This prolongs the life of the engine and reduces maintenance, enabling users to focus on the job at hand rather than frequent servicing.

Additionally, the Husqvarna 576 XP EPA III includes Smart Start technology, which ensures quick and effortless starting. The fuel pump and choke are designed to work in harmony, making it easier to start the saw with minimal effort.

Both chainsaws are designed with an ergonomic handle that provides excellent grip and comfort, reducing fatigue during extended use. The LowVib technology minimizes vibrations, further enhancing user comfort and control.

In terms of safety, both models are equipped with a chain brake that quickly stops the chain in the event of a kickback, protecting the user.

Overall, the Husqvarna 576 XP EPA III and 570 EPA III chainsaws are high-performance tools that combine advanced technology with user-friendly design, making them suitable for professionals and enthusiasts alike who demand efficiency and reliability in every cut.
Top Page Image Contents