Husqvarna 570 EPA III, 576 XP EPA III, 1152353-95 manual Federal Emission Control Warranty Statement

Page 40

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2009 and later small nonroad engine. In U.S. and Canada, new small nonroad engines must be designed, built and equipped to meet the federal stringent anti-smog standards. Husqvarna Forest & Garden must warrant the emission control system on your small nonroad engine for the period of time listed below provided there has been no abuse, neglect or improper maintenance of your unit.Your emission control system includes Parts such as the carburetor and the ignition system. Where a warrantable condition exists, Husqvarna Forest & Garden will repair your small nonroad engine at no cost to you. Expenses covered under warranty include diagnosis, parts and labor.

MANUFACTURER′S WARRANTY

COVERAGE

The 2009 and later small nonroad engines are warranted for two years. If any emission related part on you engine (as listed above) is defective, the part will be repaired or replaced by Husqvarna Forest & Garden.

OWNER′S WARRANTY RESPONSIBILITIES

As the small nonroad engine owner, you are responsible for the performance of the required maintenance listed in your Operator′s Manual. Husqvarna Forest & Garden recommends that you retain all receipts covering maintenance on your small nonroad engine, but Husqvarna Forest & Garden cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the small nonroad engine owner, you should, however, be aware that Husqvarna Forest & Garden may deny you warranty coverage if your small nonroad engine or a part of it has failed due to abuse, neglect, improper maintenance, unapproved modifications or the use of parts not made or approved by the original equipment manufacturer. You are responsible for presenting your small nonroad engine to a Husqvarna Forest & Garden authorized servicing dealer as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest & Garden at 1- 800-487-5951 or visit www.usa.husqvarna.com.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date small nonroad engine is delivered.

LENGTH OF COVERAGE

Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be performed at no

charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest & Garden at 1-800-487-5951 or visit www.usa.husqvarna.com.

WARRANTY PERIOD Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled only for regular inspection to the effect of “repair or replace as necessary” shall be warranted for 2 years. Any warranted part which is scheduled for replacement as required maintenance shall be warranted for the period of time up to the first scheduled replacement point for that part.

DIAGNOSIS The owner shall not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the diagnostic work is performed at an approved Husqvarna Forest & Garden servicing dealer.

CONSEQUENTIAL DAMAGES Husqvarna Forest & Garden may be liable for damages to other engine components caused by the failure of a warranted part still under warranty.

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper maintenance are not covered.

ADD -ON OR MODIFIED PARTS

The use of add-on or modified parts can be grounds for disallowing a warranty claim. Husqvarna Forest & Garden is not liable to cover failures of warranted parts caused by the use of add-on or modified parts.

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest & Garden at 1- 800-487-5951 or visit www.usa.husqvarna.com.

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs shall be provided at all Husqvarna Forest & Garden authorized servicing dealers.

MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS

Any Husqvarna Forest & Garden approved replacement part used in the performance of any warranty maintenance or repairs on emission-related parts, will be provided without charge to the owner if the part is under warranty.

EMISSION CONTROL WARRANTY PARTS LIST

1Carburetor and internal parts

2Intake pipe, airfilter holder and carburetor bolts.

3Airfilter and fuelfilter covered up to maintenance schedule.

4Spark Plug, covered up to maintenance schedule

5Ignition Module

MAINTENANCE STATEMENT

The owner is responsible for the performance of all required maintenance, as defined in the operator’s manual.

40 – English

Page 39 Page 41
Image 40
Page 39 Page 41
Contents EPA III 576 XP EPA KEY to Symbols Symbols on the machineSymbols in the operator’s manual You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Stop switch Cutting equipmentVibration damping system MufflerBar Cutting equipment designed to reduce kickbackChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Filling with chain oil Lubricating cutting equipmentChecking chain lubrication Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Correctly adjusted carburetor When the bar hits the stump the brake should be appliedChecking brake band wear Checking the front hand guardChecking the brake trigger Starter MufflerChanging a broken or worn starter cord Air filter Tensioning the recoil springChanging a broken recoil spring Fitting the starterAdjustment of the oil pump When making adjustmentsSpark plug Lubricating the bar tip sprocketAir Injection centrifugal cleaning Temperature 0C 32F or colderCooling system Winter useTemperature -5C 23F or colder Heated handlesElectrical carburetor heating 576XPGMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain filing and file gauges Your cutting needFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautions´z+TCG¶5S¨ Page 1152353-95

1152353-95, 570 EPA III, 576 XP EPA III specifications

The Husqvarna 576 XP EPA III and 570 EPA III chainsaws exemplify innovation in outdoor power equipment, designed for the demanding user who requires high performance and reliability. These models are ideal for professional loggers and landowners alike, combining power, efficiency, and advanced technology.

One of the standout features of the Husqvarna 576 XP EPA III is its powerful 72.2cc engine, which delivers exceptional cutting performance while maintaining low fuel consumption. This model incorporates the X-Torq technology, which reduces fuel consumption by up to 20% and decreases harmful exhaust emissions by up to 75%. This makes the 576 XP EPA III not only high-performing but also environmentally friendly, meeting stringent EPA emission requirements.

The 570 EPA III, slightly smaller at 65.1cc, still boasts impressive power and torque, making it suitable for a variety of cutting tasks. This model is also equipped with the X-Torq technology, offering fuel efficiency and reduced emissions. It’s tailored for users who need a reliable chainsaw for medium to heavy-duty jobs, providing both power and ease of use.

Both models feature an Air Injection system that uses centrifugal force to remove larger dust and debris particles before they reach the air filter. This prolongs the life of the engine and reduces maintenance, enabling users to focus on the job at hand rather than frequent servicing.

Additionally, the Husqvarna 576 XP EPA III includes Smart Start technology, which ensures quick and effortless starting. The fuel pump and choke are designed to work in harmony, making it easier to start the saw with minimal effort.

Both chainsaws are designed with an ergonomic handle that provides excellent grip and comfort, reducing fatigue during extended use. The LowVib technology minimizes vibrations, further enhancing user comfort and control.

In terms of safety, both models are equipped with a chain brake that quickly stops the chain in the event of a kickback, protecting the user.

Overall, the Husqvarna 576 XP EPA III and 570 EPA III chainsaws are high-performance tools that combine advanced technology with user-friendly design, making them suitable for professionals and enthusiasts alike who demand efficiency and reliability in every cut.
Top Page Image Contents