Husqvarna 570 EPA III, 576 XP EPA III Assembly, Fitting the bar and chain, Working with the chain

Page 16

ASSEMBLY

Fitting the bar and chain

 

!

WARNING! Always wear gloves, when

 

working with the chain.

 

 

 

 

 

Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle.

Remove the bar nuts and remove the clutch cover (chain brake). Take off the transportation ring (A).

Fit the bar over the bar bolts. Place the bar in its rearmost position. Place the chain over the drive sprocket locate it in the groove on the bar. Begin on the top edge of the bar.

Make sure that the edges of the cutting links are facing forward on the top edge of the bar.

Fit the clutch cover and locate the chain adjuster pin in the hole in the bar. Check that the drive links of the chain fit correctly over the drive sprocket and that the chain is

correctly located in the groove in the bar. Tighten the bar nuts finger tight.

Tension the chain by turning the chain tensioning screw clockwise using the combination spanner.

The chain is correctly tensioned when it does not sag from the underside of the bar, but can still be turned easily by hand. Hold up the bar tip and tighten the bar nuts with the combination spanner.

When fitting a new chain, the chain tension has to be checked frequently until the chain is run-in. Check the chain tension regularly. A correctly tensioned chain ensures good cutting performance and long life.

Note: If clutch cover is difficult to remove, replace bar nuts, engage brake and rerelease (an audible click will be heard if released properly).

16 – English

Page 15 Page 17
Image 16
Page 15 Page 17
Contents EPA III 576 XP EPA KEY to Symbols Symbols on the machineSymbols in the operator’s manual You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Stop switch Cutting equipmentVibration damping system MufflerBar Cutting equipment designed to reduce kickbackChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Filling with chain oil Lubricating cutting equipmentChecking chain lubrication Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Correctly adjusted carburetor When the bar hits the stump the brake should be appliedChecking brake band wear Checking the front hand guardChecking the brake trigger Starter MufflerChanging a broken or worn starter cord Air filter Tensioning the recoil springChanging a broken recoil spring Fitting the starterAdjustment of the oil pump When making adjustmentsSpark plug Lubricating the bar tip sprocketAir Injection centrifugal cleaning Temperature 0C 32F or colderCooling system Winter useTemperature -5C 23F or colder Heated handlesElectrical carburetor heating 576XPGMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain filing and file gauges Your cutting needFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautions´z+TCG¶5S¨ Page 1152353-95

1152353-95, 570 EPA III, 576 XP EPA III specifications

The Husqvarna 576 XP EPA III and 570 EPA III chainsaws exemplify innovation in outdoor power equipment, designed for the demanding user who requires high performance and reliability. These models are ideal for professional loggers and landowners alike, combining power, efficiency, and advanced technology.

One of the standout features of the Husqvarna 576 XP EPA III is its powerful 72.2cc engine, which delivers exceptional cutting performance while maintaining low fuel consumption. This model incorporates the X-Torq technology, which reduces fuel consumption by up to 20% and decreases harmful exhaust emissions by up to 75%. This makes the 576 XP EPA III not only high-performing but also environmentally friendly, meeting stringent EPA emission requirements.

The 570 EPA III, slightly smaller at 65.1cc, still boasts impressive power and torque, making it suitable for a variety of cutting tasks. This model is also equipped with the X-Torq technology, offering fuel efficiency and reduced emissions. It’s tailored for users who need a reliable chainsaw for medium to heavy-duty jobs, providing both power and ease of use.

Both models feature an Air Injection system that uses centrifugal force to remove larger dust and debris particles before they reach the air filter. This prolongs the life of the engine and reduces maintenance, enabling users to focus on the job at hand rather than frequent servicing.

Additionally, the Husqvarna 576 XP EPA III includes Smart Start technology, which ensures quick and effortless starting. The fuel pump and choke are designed to work in harmony, making it easier to start the saw with minimal effort.

Both chainsaws are designed with an ergonomic handle that provides excellent grip and comfort, reducing fatigue during extended use. The LowVib technology minimizes vibrations, further enhancing user comfort and control.

In terms of safety, both models are equipped with a chain brake that quickly stops the chain in the event of a kickback, protecting the user.

Overall, the Husqvarna 576 XP EPA III and 570 EPA III chainsaws are high-performance tools that combine advanced technology with user-friendly design, making them suitable for professionals and enthusiasts alike who demand efficiency and reliability in every cut.
Top Page Image Contents