Husqvarna 1152353-95, 576 XP EPA III manual Muffler, Starter, Changing a broken or worn starter cord

Page 32

MAINTENANCE

Make sure the vibration damping units are securely attached to the engine unit and handle unit.

Stop switch

Start the engine and make sure the engine stops when you move the stop switch to the stop setting.

Muffler

Never use a machine that has a faulty muffler.

Regularly check that the muffler is securely attached to the machine.

Some mufflers are equipped with a special spark arrestor screen. If your machine has this type of muffler, you should clean the screen at least once a week. This is best done with a wire brush. A blocked screen will cause the engine to overheat and may lead to serious damage.

Note! The screen must be replaced if it is damaged. If the screen is blocked the machine will overheat and this will cause damage to the cylinder and piston. Never use a machine with a muffler that is in poor condition. Never use a muffler if the spark arrestor screen is missing or defective.

The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.

Starter

WARNING! When the recoil spring is

!wound up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury.

Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective gloves.

Changing a broken or worn starter cord

•Loosen the screws that hold the starter against the crankcase and remove the starter.

•Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards.

12

•Undo the screw in the centre of the pulley and remove the pulley. Insert and fasten a new starter cord to the pulley. Wind approx. 3 turns of the starter cord onto the pulley. Connect the pulley to the recoil spring so that the end of the spring engages in the pulley. Fit the screw in the center of the pulley. Insert the starter cord through the hole in the starter housing and the starter handle. Make a secure knot in the end of the starter cord.

32 – English

Page 31 Page 33
Image 32
Page 31 Page 33
Contents EPA III 576 XP EPA KEY to Symbols Symbols on the machineSymbols in the operator’s manual You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Right hand guard Throttle lockoutChain catcher Stop switch Cutting equipmentVibration damping system MufflerChain Cutting equipment designed to reduce kickbackBar Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Checking chain lubrication Lubricating cutting equipmentFilling with chain oil Checking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Working with the chain AssemblyFitting the bar and chain Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Correctly adjusted carburetor When the bar hits the stump the brake should be appliedChecking brake band wear Checking the front hand guardChecking the brake trigger Changing a broken or worn starter cord MufflerStarter Air filter Tensioning the recoil springChanging a broken recoil spring Fitting the starterAdjustment of the oil pump When making adjustmentsSpark plug Lubricating the bar tip sprocketAir Injection centrifugal cleaning Temperature 0C 32F or colderCooling system Winter useTemperature -5C 23F or colder Heated handlesElectrical carburetor heating 576XPGMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain filing and file gauges Your cutting needFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautions´z+TCG¶5S¨ Page 1152353-95

1152353-95, 570 EPA III, 576 XP EPA III specifications

The Husqvarna 576 XP EPA III and 570 EPA III chainsaws exemplify innovation in outdoor power equipment, designed for the demanding user who requires high performance and reliability. These models are ideal for professional loggers and landowners alike, combining power, efficiency, and advanced technology.

One of the standout features of the Husqvarna 576 XP EPA III is its powerful 72.2cc engine, which delivers exceptional cutting performance while maintaining low fuel consumption. This model incorporates the X-Torq technology, which reduces fuel consumption by up to 20% and decreases harmful exhaust emissions by up to 75%. This makes the 576 XP EPA III not only high-performing but also environmentally friendly, meeting stringent EPA emission requirements.

The 570 EPA III, slightly smaller at 65.1cc, still boasts impressive power and torque, making it suitable for a variety of cutting tasks. This model is also equipped with the X-Torq technology, offering fuel efficiency and reduced emissions. It’s tailored for users who need a reliable chainsaw for medium to heavy-duty jobs, providing both power and ease of use.

Both models feature an Air Injection system that uses centrifugal force to remove larger dust and debris particles before they reach the air filter. This prolongs the life of the engine and reduces maintenance, enabling users to focus on the job at hand rather than frequent servicing.

Additionally, the Husqvarna 576 XP EPA III includes Smart Start technology, which ensures quick and effortless starting. The fuel pump and choke are designed to work in harmony, making it easier to start the saw with minimal effort.

Both chainsaws are designed with an ergonomic handle that provides excellent grip and comfort, reducing fatigue during extended use. The LowVib technology minimizes vibrations, further enhancing user comfort and control.

In terms of safety, both models are equipped with a chain brake that quickly stops the chain in the event of a kickback, protecting the user.

Overall, the Husqvarna 576 XP EPA III and 570 EPA III chainsaws are high-performance tools that combine advanced technology with user-friendly design, making them suitable for professionals and enthusiasts alike who demand efficiency and reliability in every cut.
Top Page Image Contents