Husqvarna 570 EPA III Spark plug, Lubricating the bar tip sprocket, Needle bearing lubrication

Page 34

MAINTENANCE

Spark plug

The spark plug condition is influenced by:

•Incorrect carburetor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.020 inch (0.5 mm). The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week).

When lubricating, remove the clutch cover by loosening the two bar nuts. Lay the saw on its side with the clutch drum upwards.

Lubrication involves engine oil dripping into the centre of the clutch drum as it rotates.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory set to 1 turn open. Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow.

Recommended settings:

Bar -15": 1 turn from the closed position.

Bar 15" -18": 2 turns from the closed position.

Bar 18" -24": 3 turns from the closed position.

Bar 24" -: 4 turns from the closed position.

These recommendations apply to Husqvarna’s chain oil, for other chain oils increase the oil flow by one step.

 

!

WARNING! The engine must be stopped

 

when making adjustments.

 

 

 

 

 

34 – English

Page 33 Page 35
Image 34
Page 33 Page 35
Contents EPA III 576 XP EPA Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping system Stop switchCutting equipment MufflerBar Cutting equipment designed to reduce kickbackChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Filling with chain oil Lubricating cutting equipmentChecking chain lubrication Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLimbing Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Checking brake band wear Correctly adjusted carburetorWhen the bar hits the stump the brake should be applied Checking the front hand guardChecking the brake trigger Starter MufflerChanging a broken or worn starter cord Changing a broken recoil spring Air filterTensioning the recoil spring Fitting the starterSpark plug Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketCooling system Air Injection centrifugal cleaningTemperature 0C 32F or colder Winter useElectrical carburetor heating Temperature -5C 23F or colderHeated handles 576XPGMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain filing and file gauges Your cutting needFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautions´z+TCG¶5S¨ Page 1152353-95

1152353-95, 570 EPA III, 576 XP EPA III specifications

The Husqvarna 576 XP EPA III and 570 EPA III chainsaws exemplify innovation in outdoor power equipment, designed for the demanding user who requires high performance and reliability. These models are ideal for professional loggers and landowners alike, combining power, efficiency, and advanced technology.

One of the standout features of the Husqvarna 576 XP EPA III is its powerful 72.2cc engine, which delivers exceptional cutting performance while maintaining low fuel consumption. This model incorporates the X-Torq technology, which reduces fuel consumption by up to 20% and decreases harmful exhaust emissions by up to 75%. This makes the 576 XP EPA III not only high-performing but also environmentally friendly, meeting stringent EPA emission requirements.

The 570 EPA III, slightly smaller at 65.1cc, still boasts impressive power and torque, making it suitable for a variety of cutting tasks. This model is also equipped with the X-Torq technology, offering fuel efficiency and reduced emissions. It’s tailored for users who need a reliable chainsaw for medium to heavy-duty jobs, providing both power and ease of use.

Both models feature an Air Injection system that uses centrifugal force to remove larger dust and debris particles before they reach the air filter. This prolongs the life of the engine and reduces maintenance, enabling users to focus on the job at hand rather than frequent servicing.

Additionally, the Husqvarna 576 XP EPA III includes Smart Start technology, which ensures quick and effortless starting. The fuel pump and choke are designed to work in harmony, making it easier to start the saw with minimal effort.

Both chainsaws are designed with an ergonomic handle that provides excellent grip and comfort, reducing fatigue during extended use. The LowVib technology minimizes vibrations, further enhancing user comfort and control.

In terms of safety, both models are equipped with a chain brake that quickly stops the chain in the event of a kickback, protecting the user.

Overall, the Husqvarna 576 XP EPA III and 570 EPA III chainsaws are high-performance tools that combine advanced technology with user-friendly design, making them suitable for professionals and enthusiasts alike who demand efficiency and reliability in every cut.
Top Page Image Contents