Husqvarna 575XP manual Cutting equipment, Stop switch, Muffler, General rules

Page 11

GENERAL SAFETY PRECAUTIONS

cutting equipment that is blunt or faulty (wrong type or badly sharpened) will increase the vibration level.

WARNING! Overexposure to vibration can

! lead to circulatory damage or nerve damage in people who have impaired circulation. Contact your doctor if you experience symptoms of overexposure to vibration. Such symptoms include numbness, loss of feeling, tingling, pricking, pain, loss of strength, changes in skin colour or condition. These symptoms normally appear in the fingers, hands or wrists. These symptoms may be increased in cold temperatures.

Stop switch

Use the stop switch to switch off the engine.

Muffler

The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.

WARNING! The exhaust fumes from the

! engine are hot and may contain sparks which can start a fire. Never start the machine indoors or near combustible material!

In areas with a hot, dry climate there is a high risk of fires. These areas are sometimes subject to government rules

requiring among other things the muffler must be equipped with an approved type of spark arrestor screen.

CAUTION! The muffler gets very hot during and after use. This also applies during idling. Be aware of the fire hazard, especially when working near flammable substances and/ or vapours.

WARNING! Never use a saw without a

! muffler, or with a damaged muffler. A damaged muffler may substantially increase the noise level and the fire hazard. Keep fire fighting equipment handy. If a spark arrestor screen is required in your area, never use the saw without or with a broken spark arrestor screen.

Cutting equipment

This section describes how to choose and maintain your cutting equipment in order to:

•Reduce the risk of kickback.

•Reduce the risk of the saw chain breaking or jumping off the bar.

•Obtain optimal cutting performance.

•Extend the life of cutting equipment.

•Avoid increasing vibration levels.

General rules

•Only use cutting equipment recommended by us! See instructions under the heading Technical data.

•Keep the chain’s cutting teeth properly sharpened! Follow our instructions and use the recommended file gauge. A damaged or badly sharpened chain increases the risk of accidents.

•Maintain the correct depth gauge setting! Follow our instructions and use the recommended depth gauge clearance. Too large a clearance increases the risk of kickback.

English – 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 575XP AutoTune EPA Symbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerSome terms that describe the bar and chain Cutting equipment designed to reduce kickbackBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain General advice on adjusting depth gauge settingIf the depth gauge setting is too large Adjustment of depth gauge settingChecking chain lubrication Lubricating cutting equipmentFilling with chain oil Checking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Fitting the bar and chain AssemblyFuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueCutting LimbingClearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut Directional cutsCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Checking the inertia brake release Muffler Changing a broken recoil spring StarterChanging a broken or worn starter cord Tensioning the recoil springMust always be replaced Air filterSpark plug Fitting the starterNeedle bearing lubrication Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketWinter use Air Injection centrifugal cleaningTemperature 0C 32F or colder Temperature -5C 23F or colderDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Your Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPage Page Page Page Page Page 1150861-95
Top Page Image Contents