Husqvarna 575XP manual Starting and Stopping, Starting and stopping, Cold engine, Warm engine

Page 20

STARTING AND STOPPING

Starting and stopping

WARNING! Note the following before

!starting:

The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting.

Never start a chain saw unless the bar, chain and all covers are fitted correctly. Otherwise the clutch can come loose and cause personal injuries.

Place the machine on firm ground. Make sure you have a secure footing and that the chain cannot touch anything.

Keep people and animals well away from the working area.

Cold engine

Starting: The chain brake should be activated when starting the chain saw. Activate the chain brake by pushing the front hand guard forwards.

Ignition; choke: Set the choke control in the choke position. This should automatically set the stop switch to the start position.

Start throttle: The correct choke/start throttle setting is obtained by moving the control to the choke position.

If the machine is fitted with a decompression valve (A): Press the valve to reduce the pressure in the cylinder and make starting easier. You should always use the decompression valve when starting the machine. Once the machine has

started the valve will automatically return to its closed position.

Warm engine

Use the same procedure as for starting a cold engine but without setting the choke control in the choke position. The correct choke/start throttle setting is obtained by moving the choke control to the choke position and then pushing it in again.

Starting

Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull firmly and rapidly. Never

wrap the starter cord around your hand

CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine.

Push in the choke control as soon as the engine fires and make repeated starting attempts. Immediately press and release the throttle when the engine starts. That will disengage the throttle latch.

As the chain brake is still activated the engine must return to idling speed as soon as possible by disengaging the throttle

20 – English

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 575XP AutoTune EPA Symbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesCutting equipment designed to reduce kickback BarChain Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethGeneral advice on adjusting depth gauge setting If the depth gauge setting is too largeAdjustment of depth gauge setting Tensioning the chainChecking chain lubrication Lubricating cutting equipmentFilling with chain oil Checking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Assembly Fitting the bar and chainFuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsLimbing CuttingTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Checking the inertia brake release Muffler Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAir filter Spark plugFitting the starter Must always be replacedAdjustment of the oil pump When making adjustmentsLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Temperature 0C 32F or colderTemperature -5C 23F or colder Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain filing and file gauges Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsPage Page Page Page Page Page 1150861-95
Top Page Image Contents