Husqvarna 575XP Lubricating the bar tip sprocket, Needle bearing lubrication, Cooling system

Page 35

MAINTENANCE

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week).

When lubricating, remove the clutch cover by loosening the two bar nuts. Lay the saw on its side with the clutch drum upwards.

Lubrication involves engine oil dripping into the centre of the clutch drum as it rotates.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory set to 1 turn open.

Turning the screw clockwise will reduce the oil ﬂow and turning the screw anti-clockwise will increase the oil ﬂow.

Recommended settings:

Bar -15": 1 turn from the closed position.

Bar 15" -18": 2 turns from the closed position.

Bar 18" -24": 3 turns from the closed position.

Bar 24" -: 4 turns from the closed position.

These recommendations apply to Husqvarna’s chain oil, for other chain oils increase the oil ﬂow by one step.

	!	WARNING! The engine must be stopped
	!	when making adjustments.
		when making adjustments.

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

1Air intake on the starter.

2Air guide plate.

3Fins on the ﬂywheel.

4Cooling ﬁns on the cylinder.

5Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

Note! The cooling system on a chain saw with catalytic converter must be cleaned daily. This is particularly important on chain saws with catalytic converters, because the higher exhaust temperature requires efﬁcient cooling of the engine and the catalytic converter unit.

English – 35

Image 35

Contents 575XP AutoTune EPA Symbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufﬂerSome terms that describe the bar and chain Cutting equipment designed to reduce kickbackBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain General advice on adjusting depth gauge settingIf the depth gauge setting is too large Adjustment of depth gauge settingChecking chain lubrication Lubricating cutting equipmentFilling with chain oil Checking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Fitting the bar and chain AssemblyFuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueCutting LimbingClearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut Directional cutsCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Checking the inertia brake release Mufﬂer Changing a broken recoil spring StarterChanging a broken or worn starter cord Tensioning the recoil springMust always be replaced Air ﬁlterSpark plug Fitting the starterNeedle bearing lubrication Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketWinter use Air Injection centrifugal cleaningTemperature 0C 32F or colder Temperature -5C 23F or colderDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain ﬁling and ﬁle gauges Your Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPage Page Page Page Page Page 1150861-95