Husqvarna 575XP Lubricating cutting equipment, Filling with chain oil, Checking chain lubrication

Page 15

GENERAL SAFETY PRECAUTIONS

Lubricating cutting equipment

WARNING! Poor lubrication of cutting

! equipment may cause the chain to snap, which could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal chain oil which has a vegetable oil base. We recommend the use of our own oil for both maximum chain life and to minimise environmental damage. If our own chain oil is not available, standard chain oil is recommended.

Never use waste oil! Using waste oil can be dangerous to you and damage the machine and environment.

IMPORTANT! When using vegetable based saw chain oil, dismantle and clean the groove in the bar and saw chain before long-term storage. Otherwise there is a risk of the saw chain oil oxidizing, which will result in the saw chain becoming stiff and the bar tip sprocket jamming.

Filling with chain oil

•All our chain saws have an automatic chain lubrication system. On some models the oil flow is also adjustable.

•The saw chain oil tank and the fuel tank are designed so that the fuel runs out before the saw chain oil.

However, this safety feature requires that you use the right sort of chain oil (if the oil is too thin it will run out before the fuel), and that you adjust the carburetor as recommended (a lean mixture may mean that the fuel lasts longer than the oil) and that you also use the recommended cutting equipment (a bar that is too long will use more chain oil).

Checking chain lubrication

•Check the chain lubrication each time you refuel. See instructions under the heading Lubricating the bar tip sprocket.

Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface.

If the chain lubrication is not working:

•Check that the oil channel in the bar is not obstructed. Clean if necessary.

•Check that the groove in the edge of the bar is clean. Clean if necessary.

•Check that the bar tip sprocket turns freely and that the lubricating hole in the tip sprocket is not blocked. Clean and lubricate if necessary.

If the chain lubrication system is still not working after carrying out the above checks and associated measures you should contact your servicing dealer.

English – 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 575XP AutoTune EPA KEY to Symbols Symbols on the machineSymbols in the operator’s manual EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerSome terms that describe the bar and chain Cutting equipment designed to reduce kickbackBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain General advice on adjusting depth gauge settingIf the depth gauge setting is too large Adjustment of depth gauge settingLubricating cutting equipment Filling with chain oilChecking chain lubrication Chain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Fitting the bar and chain AssemblyFuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueCutting LimbingClearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut Directional cutsCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Checking the inertia brake release Muffler Changing a broken recoil spring StarterChanging a broken or worn starter cord Tensioning the recoil springMust always be replaced Air filterSpark plug Fitting the starterNeedle bearing lubrication Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketWinter use Air Injection centrifugal cleaningTemperature 0C 32F or colder Temperature -5C 23F or colderDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Your Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPage Page Page Page Page Page 1150861-95
Top Page Image Contents