Husqvarna 1153176-26 manual Tensioning the chain, Lubricating cutting equipment

Page 13

GENERAL SAFETY PRECAUTIONS

data to find the correct depth gauge setting for your particular chain.

 

!

WARNING! The risk of kickback is

 

increased if the depth gauge setting is

 

 

too large!

 

 

 

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

 

!

WARNING! A slack chain may jump off

 

and cause serious or even fatal injury.

 

 

 

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Undo the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

Lubricating cutting equipment

WARNING! Poor lubrication of cutting ! equipment may cause the chain to snap,

which could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal chain oil which, with its vegetable oil base, is also biodegradable. We recommend the use of our own oil for both maximum chain life and to minimise environmental damage. If our own chain oil is not available, standard chain oil is recommended.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 385XP 385XPG 390XP 390XPG Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping systemCutting equipment Stop switchMuffler General rulesBar Cutting equipment designed to reduce kickbackChain Injuries Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingLubricating cutting equipment Tensioning the chainChecking chain lubrication Filling with chain oilChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Fitting the bar and chain AssemblyFitting a spike bumper Working with the chainFuel Fuel HandlingFuelling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsJam. Always stop the engine before cleaning Terms Basic cutting techniqueLimbing Tree felling techniqueSafe distance Felling directionDirectional cuts Clearing the trunk and preparing your retreatFelling cut Freeing a tree that has fallen badlyFreeing a trapped tree What is kickback? How to avoid kickbackGeneral advice Cutting trees and branches that are in tensionCutting the trunk into logs Carburettor adjustment MaintenanceGeneral Carburettor without movement limiters Recommended engine speeds are as follows Checking brake band wear When the bar hits the stump the brake should be appliedChecking the front hand guard Checking the inertia brake releaseImmediately Checking the brake triggerMuffler Changing a broken or worn starter cord StarterTensioning the recoil spring Changing a broken recoil springSpark plug Air filterFitting the starter Must always be replacedLubricating the bar tip sprocket Adjustment of the oil pumpNeedle bearing lubrication Cooling systemTemperature 0C or colder Air Injection centrifugal cleaningWinter use Heated handlesDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsApplies to Europe only EC-declaration of conformityPage Original instructions 1153176-26

1153176-26 specifications

The Husqvarna 1153176-26 is a reliable and innovative addition to the lawn care equipment market, designed specifically to meet the needs of both homeowners and professional landscapers. This product is a hedge trimmer that combines power, precision, and user-friendly features, making it an essential tool for maintaining gardens, hedges, and shrubs.

One of the key features of the Husqvarna 1153176-26 is its robust engine. It is powered by a high-performance, low-emission engine that delivers the power needed for efficient cutting while minimizing environmental impact. This focus on eco-friendliness is a significant technological advancement, setting Husqvarna apart in the competitive outdoor power equipment landscape.

The trimmer is equipped with long, dual-action blades that enhance cutting efficiency and offer improved cutting performance. The length of the blades enables users to tackle larger areas quickly, while the dual-action design reduces vibration, ensuring smoother operation and greater comfort during extended use. This design also contributes to achieving a cleaner cut, which is essential for the health of the plants being trimmed.

Another defining feature of the Husqvarna 1153176-26 is its ergonomic design. The handle is designed to provide comfort and ease of use, allowing operators to maneuver the trimmer with minimal fatigue. Additionally, the soft-grip handles ensure a secure hold, even in challenging conditions.

Safety is paramount in the design of the Husqvarna 1153176-26. The trimmer is equipped with safety features, including a safety lockout system that prevents accidental starts. This ensures that users can work without the constant worry of unintended activation, making it a safe choice for professionals and amateurs alike.

Portability and convenience are also significant considerations in the Husqvarna 1153176-26 design. The lightweight construction makes it easy to transport and operate, while the well-balanced design reduces strain on the arms and shoulders during use.

In summary, the Husqvarna 1153176-26 stands out as a high-quality hedge trimmer, blending power, efficiency, and safety in a user-friendly package. Its advanced engine technology, effective cutting blades, ergonomic design, and focus on safety make it an ideal choice for anyone looking to maintain their landscaping with precision and ease. With this equipment, users can achieve professional results while ensuring their outdoor spaces remain in pristine condition.
Top Page Image Contents